Refer to the exhibit. MPLS has been enabled on router PE11. Which of these statements is correct regarding the output display shown in the exhibit? ()
A. CEF switching is not needed for MPLS operation.
B. CEF switching is only needed to forward labeled packets.
C. CEF switching is needed on both ingress and egress interfaces on which MPLS is enabled.
D. Interface-level CEF switching is needed only on egress interfaces that are sending IP packets on which the egress LSR performs the label imposition process.
E. Interface-level CEF switching is needed only on ingress interfaces that are receiving IP packets on which the ingress LSR performs the label imposition process.
您可能感興趣的試卷
你可能感興趣的試題
A. syslog logging
B. terminal logging
C. buffered logging
D. console logging
A. Change Management
B. Security Assessment
C. Operations Assessment
D. Security Administration
E. Operations Readiness Assessment
F. Technology Assessment
Refer to the exhibit. A display of class maps for a configuration is shown in the exhibit. What will the class-map "all-traffic" match? ()
A. all voice traffic
B. all traffic with dscp 18 or dscp 43
C. all traffic with dscp 18 and dscp 43
D. all traffic with ip precedence 0 or 1
E. all traffic with ip precedence 4 and 5
A. Prepare, Plan, Create, Implement, Operate, and Improve
B. Prepare, Plan, Design, Implement, Operate, and Optimize
C. Prepare, Plan, Design, Apply, Operate, and Manage
D. Prepare, Plan, Design, Implement, Operate and Manage
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 transport protocol
E. Layer 3 destination address
A.Prepare
B.Plan
C.Design
D.Operate
A. by snooping the CoS marking on the incoming frames
B. by using RTP hello messages between the switch port and the Cisco IP Phone
C. by using CDP
D. by using DHCP snooping
E. by snooping the incoming 802.1Q VLAN tag
A.IETF
B.PFC
C.ASIC
D.TCAM
A. Features such as UplinkFast and BackboneFast are compatible with RSTP.
B. An RSTP that is based on Cisco products generally performs better than the Cisco proprietary 802.1D enhancements.
C. Cisco proprietary enhancements are not transparent.
D. Information about port roles is sent to all switches.
E. RSTPs that are based on Cisco products require no additional configuration.
A. Implement threshold monitoring using RMON.
B. Implement monitoring using SNMP or RMON.
C. Poll and record specific SNMP MIB objects from the device.
D. Verify that SNMP MIB is supported in the relevant core device.
最新試題
You are an experienced network administrator in an international corporation. During your working hours, you are asked to deploy the Cisco SSL VPN AIM module in a Cisco 1800 Series Router. The beneficial reason for that deployment is to:()
As an experienced network engineer, you are asked to troubleshoot a CIS network outage. During the troubleshooting process, you notice that one of your colleagues connects additional devices to the network with the use of his own switch. With the purpose of improving speed, the switch is attached to both network ports in an office, which leads to bridge loop.Enabling which of the following feature will be able to prevent this problem from happening again?()
In a RSTP implementation, which of the following two link types are used? ()(Choose two.)
You have just reinstalled a VIP 6-80 in a Cisco 7500 Series router. What must you do to bring up the port adapter interfaces?()
Which Cisco IOS command is used to troubleshoot a problem in which a BGP session stays in the active state?()
Refer to the exhibit. You have a non-Cisco switch that is not communicating properly while connected to the distribution-layer Cisco switching fabric.Which two best-practice actions can you take to overcome this problem? ()(Choose two.)
Which of the following allows network administrators to easily apply common services and employ features across Cisco switches, routers, and access points with an intuitive GUI?()
Which command displays only those entries in a BGP table with specific AS_PATH attributes?()
When a Cisco router is configured for SSH, it acts as an ()?
You are trying to initiate an SSH connection to a remote router and are getting rejected with an error code of 0. Which of these might be the cause of the error?()