Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command.
Which of the following is true about the effects of this configuration command?()
A. R1 will always create and flood a default route into the OSPF domain.
B. R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.
C. R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.
D. R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
您可能感興趣的試卷
你可能感興趣的試題
The following output exists on Router R1, a router internal to area 1. What can you d etermine as true from the output of the show ip ospf database summary command?()
A. The LSA was created by an ABR due to an area range command.
B. The LSA was created by an ASBR due to a summary - address command.
C. If cr eated by an area range command, the best metric for a subordinate subnet on that ABR must have been 11.
D. None of the other answers is correct.
R1, an ABR between backbone area 0 and area 1, has intra - area routes in area 0 for 10.1.1.0/24,10.1.2.0/24, and 10.1.3.0/24. These routes have metrics of 21, 22, and 23, respectively. An engineer then adds the area 0 r ange 10.1.0.0 255.255.0.0 command under the OSPF process of R1.
Which of the following is true?()
A. R1 loses and then re - establishes neighborships with all neighbors.
B. R1 no longer advertises 10.1.1.0/24 to neighbors into area 1.
C. R1 advertises a 1 0.1.0.0/16 route into area 1 with a metric of 23 (largest metric).
D. R1 advertises a 10.1.0.0/16 route into area 1 with metric of 21 (lowest metric).
Use the same scenario as the previous question, w ith one changE.Instead of the distribute-list prefix question in command configured on R1,R1's OSPF process has an area 1 filter-list prefix question in commandconfigured. Again assuming that the subnets listed in the answers actually exist in area 0.
Which of the following occurs on router R1?()
R1#sh ip prefix - list
ip prefix - list question: 4 entries
seq 5 deny 10.1.2.0/24 ge 25 le 27
seq 15 deny 10.2.0.0/16 ge 30 le 30
seq 20 permit 0.0.0.0/0 le 32
A. R1 will not create/flood a type 3 LSA for su bnet 10.1.2.0/26 into area 1
B. R1 will not create/flood a Type 3 LSA for subnet 10.1.2.0/24 into area 1
C. R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablE
D. R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE
The following command output was gathered from Router R1, an ABR between areas 0 (backbone) and area 1. In this internetwork, area 0 contains all the subnets of cla ss A network 10.0.0.0. R1's OSPF process has a distribute - list prefix question in command configured. Assuming the subnets listed in the answers actually exist in area 0.
Which of the following occurs on router R1?()
R1#sh ip prefix - list
ip prefix - list question: 4 entries
seq 5 deny 10.1.2.0/24 ge 25 le 27
seq 15 deny 10.2.0.0/16 ge 30 le 30
seq 20 permit 0.0.0.0/0 le 32
A. R1 will not create/flood a type 3 LSA for subnet 10.1.2.0/26 into area 1
B. R1 will not create/flood a Type 3 LSA for subnet 1 0.1.2.0/24 into area 1
C. R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablE
D. R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE
Router B1, an internal router in area 1, displays the following output. The only two ABRs connected to area 1 are performing Type 3 LSA filterinG. Which of the following answers is true based on the information in the output from B1?()
R1# show ip route 10.1.0.0 255.255.0.0 longer - prefixes
! Legend lines omitted for brevity
10.0.0.0/8 is variably subnetted, 17 subnets, 3 masks
O 10.1.2.0/24 [110/658] via 10.10.13.1, 00:00:32, Serial0/0/0.1
O IA 10.1.1.0/24 [110/658] via 10.10.23.2, 00:41:39, Ser ial0/0/0.2
O IA 10.1.3.0/24 [110/658] via 10.10.23.2, 00:41:39, Serial0/0/0.2
A. A Type 3 LSA for 10.2.2.0/24 was filtered by both ABRs
B. A Type 3 LSA for 10.1.2.0/24 was not filtered by both ABRs
C. A Type 3 LSA for 10.1.3.0/24 was not filtered by at least one ABR
D. A Type 3 LSA for 10.1.1.0/24 filtered by both ABRs
Which of the following LSA types describe information related to topology or subnets useful for calculating routes for subnets inside the OSPF domain?()
A. 1
B. 2
C. 3
D. 4
E. 5
F. 7
The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?()
R3#show ip ospf interface brief
Interface PID Area IP Address/Mask Cost State Nbrs F/C
Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1
Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1
Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1
A. An a uto - cost reference - bandwidth 1000 command in router ospf mode
B. An auto - cost reference - bandwidth 2000 command in router ospf mode
C. An ip ospf cost 1000 interface S0/0/0.1 command in router ospf mode
D. An auto - cost reference - bandwidth 64700 command i n router ospf mode
Which of the following LSA types describes topology information that, when changed, requires a router in the same area to perform an SPF calculation?()
A. 1
B. 2
C. 3
D. 4
E. 5
F. 7
R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2.
Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?()
A. R2's Type 1 LSA
B. Subnet 10.1.1.0/24's Type 2 LSA
C. ABR1's Type 1 LSA in area 0
D. Subnet 10.1.1.0/24's Type 3 LSA in Area 0
E. Subnet 10.1.1.0/24's Type 3 LSA in Area 1
Routers R1, R2, R3, and R4 connect to the same 10.10.10.0/24 LAN- based subnet. OSPF is fully working in the subnet. Later, R5, whose OSPF priority is higher than the other four routers, joins the subnet.
Which of the following are true about the OSPF database exchange process over this subnet at this point?()
A. R5 will send its DD, LSR, and LSU packets to the 224.0.0.5 all - DR - routers multicast address.
B. R5 will send its DD, LSR, and LSU pack ets to the 224.0.0.6 all - DR - routers multicast address.
C. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU packets to the 224.0.0.6 all- SPF - routers multicast address.
D. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU pa ckets to the 224.0.0.5 all- SPF - routers multicast address.
最新試題
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?()
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?()
Which of the following answers lists a multicast IPv6 address?()
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?()
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?()
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output?()B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1