單項選擇題

R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2.
Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?()

A. R2's Type 1 LSA
B. Subnet 10.1.1.0/24's Type 2 LSA
C. ABR1's Type 1 LSA in area 0
D. Subnet 10.1.1.0/24's Type 3 LSA in Area 0
E.  Subnet 10.1.1.0/24's Type 3 LSA in Area 1


您可能感興趣的試卷

你可能感興趣的試題

1.多項選擇題

Routers R1, R2, R3, and R4 connect to the same 10.10.10.0/24 LAN- based subnet. OSPF is fully working in the subnet. Later, R5, whose OSPF priority is higher than the other four routers, joins  the subnet.
Which of the following are true about the OSPF database exchange process over this subnet at this point?()

A. R5 will send its DD, LSR, and LSU packets to the 224.0.0.5 all - DR - routers multicast address.
B. R5 will send its DD, LSR, and LSU pack ets to the 224.0.0.6 all - DR - routers multicast address.
C. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU packets to the 224.0.0.6 all- SPF - routers multicast address.
D. The DR will inform R5 about LSAs by sending its DD, LSR, and LSU pa ckets to the 224.0.0.5 all- SPF - routers multicast address.

3.單項選擇題

A verification  plan shows a network diagram with branch office Routers B1 through B100, plus two ABRs, ABR1, and ABR2, all in area 100. The branches connect to the ABRs using Frame Relay point - to - point subinterfaces. The verification plan lists the output of the show i p ospf database summary 10.100.0.0 command on a router B1, one of the branches.
Which of the following is true regarding the output that could be listed for this command?()

A. The output lists nothing unless 10.100.0.0 has been configured as a summary rou te using the area range command.
B. If 10.100.0.0 is a subnet in area 0, the output lists one Type 3 LSA, specifically the LSA with the lower metric when comparing ABR1's and ABR2's LSA for 10.100.0.0.
C. If 10.100.0.0 is a subnet in area 0, the output lists two Type 3 LSAs, one each created by BR1 and ABR2.
D. None, because the Type 3 LSAs would exist only in the ABR's LSDBs.

4.單項選擇題

A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG.
For which of the following cases would you expect a router to create and flood a Type 2 LSA?()

A. When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.
B.  When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.
C. When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.
D. When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.
E. None of the other answers is correct.

6.單項選擇題

A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC.
Which of the following is true about OSPF in this design?()

A. The central site router has 100 fully adjacent neighborships with the 100 branches
B. The central  site router has neighborships with all branch routers, but fully adjacent neighbors with only two branches
C. The central site router has a neighborship with the Frame Relay switcH
D. None of the other answers is correct

7.單項選擇題Which of the following settings do not prevent two potential OSPF neighbors from becoming neighbors?()

A. The interface used to connect to that neighbor being passive in the OSPF process
B. Duplicate OSPF router IDs
C. Mismatched dead timers
D. IP addr esses of 10.1.1.1/24 and 10.2.2.2/24
E. Mismatched OSPF process IDs

8.多項選擇題

Routers R1 and R2, OSPF neighbors in area 0 over their Fa0/0 interfaces (respectively), currently both successfully use OSPF MD5 authentication. The OSPF configuration includes the area 0 authentication command under the router ospf 1 command.
Which of the following commands must have been configur ed on R1's Fa0/0 interface?()

A. ip ospf authentication null
B. ip ospf authentication message - digest
C. ip ospf authentication -key whatever- it - is
D. ip ospf message - digest - key 1 md5 whatever - it - is
E. ip ospf md5 1 key whatever - it - is

9.多項選擇題

Routers R1 and R2 are OSPF neighbors using their Fa0/0 interfaces, respectively, using default settings for all timers. An engineer ad ds the ip ospf hello - interval 6 command to R1's Fa0/0 configuration.
Which of the following is true regarding the results from this change?()

A. The show ip ospf neighbor command on R1 lists the revised Hello timer
B. The show ip ospf interfac e brief command on R1 lists the revised Hello timer
C. The R1 - R2 neighborship fails due to Hello timer mismatcH
D. The show ip ospf interface command on R1 lists the revised Hello timer

10.多項選擇題

Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers.
Which of the  following is true on R1?()

A. The show ip ospf neighbors command lists two neighbors off Fa0/0.
B. The show ip ospf neighbors command lists four neighbors off Fa0/0.
C. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.
D. The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.

最新試題

A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?()

題型:?jiǎn)雾?xiàng)選擇題

Look at the following configuration below and select the statements that are true.()RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0

題型:多項選擇題

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1

題型:?jiǎn)雾?xiàng)選擇題

The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1

題型:?jiǎn)雾?xiàng)選擇題

Which of the following  answers lists a multicast IPv6 address?()

題型:?jiǎn)雾?xiàng)選擇題

An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()

題型:?jiǎn)雾?xiàng)選擇題

Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?()

題型:?jiǎn)雾?xiàng)選擇題

An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?()

題型:?jiǎn)雾?xiàng)選擇題

Which of the following must match for  two directly connected routers running OSPF to establish a neighbor adjacency?()

題型:多項選擇題

Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?()

題型:?jiǎn)雾?xiàng)選擇題