Refer to the exhibit. Which st atement is true?（）
A. Router RTA is the BDR
B. Router RTA is directly connected to interface 192.168.45.1
C. Neighbor 192.168.45.1 has changed its OSPF priority number
D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Which statement is true about the configuration? （）
A. RTA will not establish an OSPF adjacency w ith RTB
B. RTA will send OSPF hello packets, but will not send OSPF updates
C. RTA will not accept OSPF hello packets from RTB
D. RTA will send OSPF updates, but will not establish an adjacency with RTB
A. Ensure that an interface has been configured with an IP address
B. Ensure that IP classless is enabled
C. Ensure that the interfaces can ping their directly connected neighbors
D. Ensure that an interface has been configured with an IP address and is up
Open Shortes t Path First (OSPF) is a routing protocol developed for Internet Protocol (IP) networks by the Interior Gateway Protocol (IGP) working group of the Internet Engineering Task Force (IETF).
Which two statements best describe the OSPF link - state routing pro tocol?（）
A. OSPF sends updates every 10 seconds
B. OSPF sends triggered updates when a network change occurs
C. When a link state is changed, the router that detected the change creates a link - state advertisement (LSA) and propagates it to all OSPF devices using the 224.0.0.6 multicast address
D. OSPF sends summaries of individual link- state entries every 30 minutes to ensure LSDB synchronization
OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）
A. The ip ospf network broadcast command should be configured on each Frame Relay interface
B. The ip ospf network non -broadcast command should be configured on each Frame Relay interface
C. Th e ip ospf priority value on the spoke routers should be set to 0
D. The ip ospf priority value on the hub router should be set to 0
E. The neighbor command should be configured under the OSPF routing process on all routers
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:
*Mar 1 00:2 5:01.084: %OSPF -4- ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0 .How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?（）
A.R1(config - router)# area 0 virtual - link 1.1.1.1 R3(config - router)# area 2 virtual - link 3.3.3.3
B.R1(config - router)# area 1 virtual - link 2.2.2.2 R3(config - router)# area 1 virtual - link 2.2.2.2
C.R1(config - router)# area 1 virtual - link 20.20 .20.2 R3(config - router)# area 1 virtual - link 30.30.30.2
D.R1(config - router)# area 1 virtual - link 30.30.30.3 R3(config - router)# area 1 virtual - link 20.20.20.1
E.R1(config - router)# area 1 virtual - link 3.3.3.3 R3(config - router)# area 1 virtual - link 1.1 .1.1
DR (Designated Router) is for environments where many routers on the same network such as Ethernet. In the following presented network, all routers are reloaded simultaneously, and DR is selected as expected. What is the RTC status?（）
A. 2WAY/DR
B. FULL/DR
C. FULL/DROTHER
D. FULL/BDR
A. show ip ospf interfaces
B. show ip ospf protocols
C. show ip ospf neighbors
D. show ip ospf database
A. less frequent SPF calculations
B. fewer hello packets
C. smaller routing tables
D. reduced LSU overhe ad
E. fewer adjacencies needed
A. show ip ospf database external
B. show ip ospf database nssa - external
C. show ip route ospf
D. show ip ospf datab ase summary
E. show ip route
Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?（）
A. On the ABR router ospf 10 area 3 stub
B. On all Area 3 routers router ospf 10 area 3 stub
C. On all Area 3 routers router ospf 10 area 3 stub no - summary
D. On the ABR router ospf 10 area 3 nssa
E. On the ABR rou ter ospf 10 area 3 stub no - summary
最新試題
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64