A. Automatic 6to4, quartets 2 and 3
B. Automatic 6to4, quartets 7 and 8
C. ISATAP, quartets 2 and 3
D. ISATAP, quartets 7 and 8
您可能感興趣的試卷
你可能感興趣的試題
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）
interface loopback 1
ip address 192.168.1.1 255.255.255.255
interface tunnel 2
ipv6 address 2002:C0A8:10 1::1/64
tunnel source loopback 1
A. Automatic 6to4
B. Manually configured tunnel
C. ISATAP
D. GRE
A. Automatic 6to4
B. Manually configured tunnel
C. ISATAP
D. GRE
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.
Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
A. tunnel source
B. tunnel destination
C. tunnel mode
D. All these commands are requireD
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）
interface loopback 1
ip address 1.1.1.1 255.255.255.255
interface tunnel 2
ipv6 address 2000::1::/64
tunnel source loopback 1
tunnel destina tion 2.2.2.2
tunnel mode ipv6ip
ipv6 eigrp 1
A. Automatic 6to4
B. Manually configured tunnel
C. ISATAP
D. GRE
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
E. Dual stacks
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.
Which of the following tools would be most appropriate?（）
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.
Which of the fol lowing tools would be most appropriate?（）
A. Native IPv6
B. Point - to -point tunnels
C. Multipoint tunnels
D. NAT - PT
A. Metric
B. Administrative distance
C. Timeout (seconds)
D. Prefix length
E. Interface ID
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）
D 2000::/64 [90/1422516]
via FE80::213:19FF:FE7B:5026, Serial0/0/
1
C 2000:0:0:1::/64 [0/0]
via Serial0/0/1, directly connected
L 2000::1:213:19FF:FE7B:5004/128 [0/0]
via Serial0/0/1, receive
A. Route 2000::/64 will be redistributed.
B. Route 2 000:0:0:1::/64 will be redistributed.
C. Route 2000:1:213:19FF:FE7B:5004/128 will be redistributed.
D. No routes will be redistributed because of the omission of the subnets parameter of the redistribute command.
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）
ipv6 router ospf 1
ipv6 unicast- routing
interface f0/0
ipv6 address 2000 ::1/64
ipv6 ospf 1 area 1
interface s0/0/0
ipv6 address 2001::/64 eui - 64
ipv6 ospf 1 area 0
A. OSPF works on F0/0 and S0/0/0 without further configuration
B. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE
C. OSPF works with the addition of one command: an router - id command in OSPF router configuration modE
D. OSPFv3 needs at least two more configuration commands before it works on R1
最新試題
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0