A. R 12.18.8.0/24 [120/1] via 12.18.2., 00:00:10, Serial0
B. R 12.18.11.0/24 [120/7] via 12.18.9.1, 00:00:03, Serial1
C. C 12.18.1.0/24 is directly connected, Ethernet0
D. R 12.18.5.0/24 [120/15] via 12.18.2.2, 00:00:10, Serial0
您可能感興趣的試卷
你可能感興趣的試題
You are a network technician at TestKing, Inc. You are currently troubleshooting a routing issue on the Testking1 router. You issue the show ip route command. The output from the command is displayed in the following exhibit:
Which one of the following routes WILL NOT be entered into its neighboring routers routing table?()
A. R 192.168.11.0/24 [120/7] via 192.168.9.1, 00:00:03, Serial1
B. C 192.168.1.0/24 is directly connected, Ethernet0
C. R 192.168.8.0/24 [120/1] via 192.168.2.2, 00:00:10, Serial0
D. R 192.168.5.0/24 [120/15] via 192.168.2.2, 00:00:10, Serial0
E. None of the above
You are a network administrator at TestKing, Inc. and you're getting complaintsthat users on the TestKing2 Ethernet network can't access the TestKing1 site. Totroubleshoot this, you begin by looking at the Testking1 and Testking2 routerconfigurations as shown below:
Based on the above output, what is the underlying cause of this problem?()
A. Link state routing protocol is missing.
B. Incorrectly configured IP addresses
C. IGRP is incorrectly configured.
D. Frame relay is not configured.
E. None of the above
A. The IP addresses of workstations allowed gain access to the router via an access list
B. Permanent name-to-address mappings created using the ip host command.
C. Temporary and permanent DNS entries.
D. The names of the routers created using the hostname command.
E. The length of time of users logged into the router, as well as the duration
A. application layer
B. session layer
C. transport layer
D. internet layer
E. network layer
F. data link layer
G. physical layer
A. The Popcorn router is not forwarding RIP updates.
B. The Popcorn router did not include network 192.168.12.0 in its routing configuration.
C. The Ethernet1 interface of the Popcorn router is shutdown.
D. The clockrate is not present in the configuration of one of the routers.
E. The Serial interface of the Popcorn router is not operating.
A. TK1#show ip eigrp adjacency
B. TK1#show ip eigrp topology
C. TK1#show ip eigrp interfaces
D. TK1#show ip eigrp neighbors
E. None of the above
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:
TK1(config)# router ospf 1
TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0
After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?()
A. The AS is not correctly configured
B. The network subnet mask is incorrectly configured
C. The network wildcard mask is configured incorrectly
D. The network number is not correctly configured
E. The process id is configured incorrectly
F. None of the above
On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?()
A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.
While trying to diagnose a routing problem in the network, you issue RIP debugging as displayed below:
RtrA#debug ip rip
Rip protocol debugging is on
RtrA#
1d05h: RIP: sending v1 update to 255.255.255.255 via FastEthernet0/0 (172.16.1.1)
1d05h: RIP: build update entries
1d05h: network 10.0.0.0 metric 1
1d05h: network 192.168.1.0 metric 2
1d05h: RIP: sending v1 update to 255.255.255.255 via Serial0/0 (10.0.8.1)
1d05h: RIP: build update entries
1d05h: network 172.16.0.0 metric 1
RtrA#
1d05h: RIP: received v1 update from 10.0.15.2 on Serial0/0
1d05h: 192.168.1.0 in 1 hops
1d05h: 192.168.0 in 16 hops (inaccessible)
Based on the output of the above exhibit, which two of the following statements are true?()
A. A ping to 10.0.15.2 will be successful.
B. RtrA has three interfaces that will take part in the RIP process.
C. There are at least two routers participating in the RIP process.
D. A ping to 192.168.168.2 will be successful.
A. TK1# show ip ospf interface
B. TK1# show ip ospf priority
C. TK1# show ospf neighbor detail
D. TK1# show ospf processes
E. TK1# show ospf neighbor state
最新試題
Which of the following host addresses are member of networks that can be routed across the public Internet? ()
Which connections allow the use of full-duplex Ethernet?()
The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? ()
Which of the following describe router functions?()
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
All WAN links is side the TestKing.com network use PPP with for authentication security. Which command will display the CHAP authentication process as it occurs between two routers in the network?()
What is a global command?()
What feature of a networks switch allows an administrative to create separate broadcast domains?()
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?()
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?()