多項選擇題The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?()

A. The Popcorn router is not forwarding RIP updates.
B. The Popcorn router did not include network 192.168.12.0 in its routing configuration.
C. The Ethernet1 interface of the Popcorn router is shutdown.
D. The clockrate is not present in the configuration of one of the routers.
E. The Serial interface of the Popcorn router is not operating.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題Which one of the following EIGRP commands can check the IP addresses of the adjacent neighbors, as well as verifying the EIGRP retransmit intervals and queue counts?()

A. TK1#show ip eigrp adjacency
B. TK1#show ip eigrp topology
C. TK1#show ip eigrp interfaces
D. TK1#show ip eigrp neighbors
E. None of the above

2.單項選擇題

A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:
TK1(config)# router ospf 1
TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0
After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?()

A. The AS is not correctly configured
B. The network subnet mask is incorrectly configured
C. The network wildcard mask is configured incorrectly
D. The network number is not correctly configured
E. The process id is configured incorrectly
F. None of the above

3.單項選擇題

On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?()

A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.


5.單項選擇題Which one of the following privileged EXEC mode IOS show commands will display the state of the OSPF DR/BDR (designated router / backup designated router) election process?()

A. TK1# show ip ospf interface
B. TK1# show ip ospf priority
C. TK1# show ospf neighbor detail
D. TK1# show ospf processes
E. TK1# show ospf neighbor state

6.多項選擇題To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met?()

A. Each end of the trunk line must be set to IEEE 802.1E encapsulation.
B. The VTP management domain name of both switches must be set the same.
C. All ports on both the switches must be set as access port.
D. One of the two switches must be configured as a VTP server.
E. A rollover cable is required to connect the two switches together.
F. A router must be used to forward VTP traffic between VLANs.

7.多項選擇題Which router IOS commands can be used to troubleshoot LAN connectivity problems?()

A. Ping
B. Tracert
C. Ipconfig
D. Show ip route
E. Winipcfg
F. Show interfaces

8.多項選擇題You are attempting to troubleshoot some problems within your local network.Which of the following are router IOS commands that can be used to troubleshoot LAN connectivity problems?()

A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfg
F. show interfaces
G. All of the above

9.單項選擇題What command verifies connectivity between two hosts by sending and receiving ICMP echo messages?()

A. ping
B. tracert
C. netstat
D. show cdp neighbors detail
E. show ip route
F. traceroute

10.單項選擇題A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?()

A. The switch port link lights will be off on both switches indicating the ports are not connected.
B. The switch port link light will be off on one switch indicating that STP has disabled the port.
C. The switch port link lights will flash amber indicating an error.
D. The switch port link lights will be green indicating normal operation.

最新試題

Which statement describes the rule of split horizon?()

題型:單項選擇題

What does a configuration Register Setting of 0x2105 indicate to the Router? ()

題型:單項選擇題

The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? ()

題型:單項選擇題

A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? ()

題型:單項選擇題

Which command is used to display the placement and direction of an IP access control list on a router?()

題型:單項選擇題

TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.()

題型:多項選擇題

Which of the following contribute to congestion on an Ethernet network?()

題型:多項選擇題

Which of the following describe router functions?()

題型:多項選擇題

Which connections allow the use of full-duplex Ethernet?()

題型:多項選擇題

New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? ()

題型:單項選擇題