A. ROM, Flash, NVRAM
B. ROM, TFTP server, Flash
C. Flash, TFTP server, ROM
D. Flash, NVRAM, RAM
您可能感興趣的試卷
你可能感興趣的試題
A. Make sure that the network server can be accessed.
B. Check that the authentication for access is set.
C. Assure that the network server has adequate space for the code image.
D. Verify any file naming and path requirements.
E. Make sure that the server can load and run the bootstrap code.
A. Router# show version
B. Router# show flash
C. Router# show memory
D. Router# show buffers
E. Router# show running-config
F. All of the above
After logging into the RtrB router, you issue the "show interface" command as displayed below:
After considering the effects of the command output illustrated in the exhibit above,which of the following protocols are operational on the serial link?（）
A. PPP
B. IP
C. Compression
D. IPX
E. Multilink
F. ATX
A. Distribution channel failures
B. Feature capabilities
C. Memory capacity needs
D. Hardware product platform
E. Programming language requirements
F. Run location and compression status
A. The memory capacity requirements
B. The hardware product platform
C. The distribution channel
D. The feature capabilities
E. The run location and compression status
A. Router# copy tftp flash
B. Router# copy flash run
C. Router(config)# restore flash
D. Router(config)# repair flash
E. Router#copy flash tftp
F. Router# copy start flash
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.
What is the most likely cause of this?（）
A. The NVRAM is corrupted.
B. The boot system commands were omitted in the configuration.
C. The configuration register setting is incorrect.
D. The upgraded configuration incompatible with the hardware platform.
E. The upgraded IOS incompatible with the hardware.
A. Router# show IOS
B. Router# show version
C. Router# show image
D. Router# show protocols
E. Router# show flash
A. It is used to restart the router.
B. It is used to bypass the configuration in NVRAM.
C. It is used to enter ROM Monitor mode.
D. It is used to view the lost password.
E. It is used to save the changes to the configuration.
A. Type exit at the setup dialog.
B. Type close at the setup dialog.
C. Press the Ctrl-C key combination.
D. Press the Ctrl-X key combination.
E. Issue the copy startup-config command.
F. Issue the 'write e" command.
G. Issue the "write mem" command
最新試題
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）
What is a global command?（）
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）
What is the subnetwork address for a host with IP address 201.100.5.68/28?（）
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?（）
What does a configuration Register Setting of 0x2105 indicate to the Router? （）
What feature of a networks switch allows an administrative to create separate broadcast domains?（）
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）