A. Make sure that the network server can be accessed.
B. Check that the authentication for access is set.
C. Assure that the network server has adequate space for the code image.
D. Verify any file naming and path requirements.
E. Make sure that the server can load and run the bootstrap code.
您可能感興趣的試卷
你可能感興趣的試題
A. Router# show version
B. Router# show flash
C. Router# show memory
D. Router# show buffers
E. Router# show running-config
F. All of the above
After logging into the RtrB router, you issue the "show interface" command as displayed below:
After considering the effects of the command output illustrated in the exhibit above,which of the following protocols are operational on the serial link?()
A. PPP
B. IP
C. Compression
D. IPX
E. Multilink
F. ATX
A. Distribution channel failures
B. Feature capabilities
C. Memory capacity needs
D. Hardware product platform
E. Programming language requirements
F. Run location and compression status
A. The memory capacity requirements
B. The hardware product platform
C. The distribution channel
D. The feature capabilities
E. The run location and compression status
A. Router# copy tftp flash
B. Router# copy flash run
C. Router(config)# restore flash
D. Router(config)# repair flash
E. Router#copy flash tftp
F. Router# copy start flash
After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.
What is the most likely cause of this?()
A. The NVRAM is corrupted.
B. The boot system commands were omitted in the configuration.
C. The configuration register setting is incorrect.
D. The upgraded configuration incompatible with the hardware platform.
E. The upgraded IOS incompatible with the hardware.
A. Router# show IOS
B. Router# show version
C. Router# show image
D. Router# show protocols
E. Router# show flash
A. It is used to restart the router.
B. It is used to bypass the configuration in NVRAM.
C. It is used to enter ROM Monitor mode.
D. It is used to view the lost password.
E. It is used to save the changes to the configuration.
A. Type exit at the setup dialog.
B. Type close at the setup dialog.
C. Press the Ctrl-C key combination.
D. Press the Ctrl-X key combination.
E. Issue the copy startup-config command.
F. Issue the 'write e" command.
G. Issue the "write mem" command
After working all night and successfully configuring a Cisco router for the TestKing network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode!
Which of the choices below indicates the source of your problem?()
A. Hardware failure in NVRAM prevents the router from loading the config
B. Startup-config in flash is corrupt and cannot be analyzed
C. Router configuration-register set to bypass startup configuration
D. Startup-config in NVRAM is corrupt and cannot be analyzed
E. None of the above
最新試題
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?()
What is the subnetwork address for a host with IP address 201.100.5.68/28?()
Which of the following contribute to congestion on an Ethernet network?()
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?()
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?()
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()
Given a subnet mask of 255.255.255.224, which of the following addresses can be assigned to network hosts?()
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
All WAN links is side the TestKing.com network use PPP with for authentication security. Which command will display the CHAP authentication process as it occurs between two routers in the network?()
Which command is used to display the placement and direction of an IP access control list on a router?()