After working all night and successfully configuring a Cisco router for the TestKing network you save your changes on the startup config, reboot the router, and go out for a cigarette. When you return, none of your changes are active and the router boots to the initial configuration mode!
Which of the choices below indicates the source of your problem?()
A. Hardware failure in NVRAM prevents the router from loading the config
B. Startup-config in flash is corrupt and cannot be analyzed
C. Router configuration-register set to bypass startup configuration
D. Startup-config in NVRAM is corrupt and cannot be analyzed
E. None of the above
您可能感興趣的試卷
你可能感興趣的試題
A. ROM Monitor mode
B. SETUP mode
C. Autoflash mode
D. RXBOOT mode
E. None of the above
A. Show history
B. Show buffers
C. Show typed commands
D. Show terminal buffer
E. Show command
A. It will recall the previous command line
B. It will move the cursor one line up
C. It will redisplay the current command line
D. It will capitalize the command line
E. None of the above
A. RAM should be erased and the router restarted.
B. Flash should be erased and the router restarted.
C. NVRAM should be erased and the router restarted.
D. The new configuration should be entered and saved.
A. A command that can be entered in any configuration mode.
B. A command that supports all protocols.
C. A command that is implemented in all IOS versions.
D. A command that is set once and affects the entire router.
E. A command that is available in every release of IOS.
A. >
B. #
C. ?
D. *
E. All of the above
F. None of the above
A. Defines the network topology
B. Access to network resources
C. Routing and switching functions
D. Content Filtering
E. Intrusion Detection
A. show boot
B. show flash
C. show register
D. show version
E. show config
You are the administrator of the Testking network and you have forgotten the password to one of your routers. After completing the password recovery procedure the router returned to its normal operation. The config-register was set back to the initial default value.
What is this value?()
A. 0x2112
B. 0x2104
C. 0x2102
D. 0x2142
E. 0x2100
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.
Which of the conditions below have to be met in order for this to occur?()
A. The switch that will share the VLAN information must be in the VTP Server mode.
B. The switches must be in the same VTP domain.
C. The switch that will share the VLAN information must be configured as the root bridge.
D. The switches must be configured to use the same VTP version.
E. The switches must be configured to use the same STP version.
F. The switches must be configured to use the same type of ID tagging.
G. The switches must be connected over VLAN trunks.
最新試題
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()
A Class C network address has been subnetted with a /27 mask.Which of the following addresses is a broadcast address for one of the resulting subnets?()
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
Which of the following correctly describe steps in the OSI data encapsulation process?()
Which of the following options lists the steps in PPP session establishment in the correct order?()
What does a configuration Register Setting of 0x2105 indicate to the Router? ()
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.()
Which statement describes the rule of split horizon?()
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? ()
Which connections allow the use of full-duplex Ethernet?()