A. The exchange of advertisement is triggered by a change in the network.
B. All routers exchange routing tables with each other iIn a multipoint network.
C. Packets are routed based upon the shortest path to the destination.
D. Paths are chosen depending on the cost efficiency factor.
E. Every router in an OSPF area is capable of representing the entire network topology.
F. Only the designated router in an OSPF area can represent the entire network topology.
您可能感興趣的試卷
你可能感興趣的試題
A. Distance vector protocols send the entire routing table to directly connected neighbors.
B. Distance vector protocols are responsible for sending updates to all networks listed in the routing table.
C. Link state protocols are responsible for sending the entire routing table to the whole network.
D. Link state protocols send updates regarding their own links status to all other routers on the network.
A. The IP address of the first Fast Ethernet interface.
B. The IP address of the console management interface.
C. The highest IP address among its active interfaces.
D. The lowest IP address among its active interfaces.
E. There will be no router ID until a loopback interface is configured.
A. Point-to-point
B. Broadcast multicast
C. Nonbroadcast multicast
D. Backbone area 0
E. Virtual Link
A. The RIP route
B. The static route
C. The IGRP route
D. All three will load balance.
A. 15
B. 16
C. 99
D. 255
E. Unlimited
A. Neighbor Table
B. SRF Table
C. RTP Table
D. Topology Table
E. Query Table
F. Dual Table
A. Only routers can split boundaries (horizons) between networks in separate AS numbers.
B. Each AS must keep routing tables converged to prevent dead routes from being advertised across boundaries.
C. Once a route is received on an interface, advertise that route as unreachable back out the same interface.
D. Information about a route should never be sent back in the direction from which the original update came.
A. IGRP
B. CDP
C. OSPF
D. RIP v1
E. RIP v2
F. EIGRP
A. Router(config-router)# network 192.168.10.0 0.0.0.255 0
B. Router(config-router)# network 192.168.10.0 0.0.0.255 area 0
C. Router(config-router)# network 192.168.10.0 255.255.255.0 area 0
D. Router(config)# router ospf 0
E. Router(config)# router ospf 1
A. Allows interfaces to share common IP addresses.
B. Allows an interface to remain up without the aid of keepalives.
C. Allows a router to send routing and not receive updates via that interface.
D. Allows a routing protocol to forward updates that is missing its IP address.
E. Allows a router to receive routing updates on an interface but not send updates via that interface.
最新試題
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?()
Which statement describes the rule of split horizon?()
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?()
Which connections allow the use of full-duplex Ethernet?()
How many usable sub network and usable hosts per subnet result in the network address 201.105.13.0 is sub netted with a mask of /26? ()
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?()
Which of the following host addresses are member of networks that can be routed across the public Internet? ()
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
What is a global command?()