A. Distance vector protocols send the entire routing table to directly connected neighbors.
B. Distance vector protocols are responsible for sending updates to all networks listed in the routing table.
C. Link state protocols are responsible for sending the entire routing table to the whole network.
D. Link state protocols send updates regarding their own links status to all other routers on the network.
您可能感興趣的試卷
你可能感興趣的試題
A. The IP address of the first Fast Ethernet interface.
B. The IP address of the console management interface.
C. The highest IP address among its active interfaces.
D. The lowest IP address among its active interfaces.
E. There will be no router ID until a loopback interface is configured.
A. Point-to-point
B. Broadcast multicast
C. Nonbroadcast multicast
D. Backbone area 0
E. Virtual Link
A. The RIP route
B. The static route
C. The IGRP route
D. All three will load balance.
A. 15
B. 16
C. 99
D. 255
E. Unlimited
A. Neighbor Table
B. SRF Table
C. RTP Table
D. Topology Table
E. Query Table
F. Dual Table
A. Only routers can split boundaries (horizons) between networks in separate AS numbers.
B. Each AS must keep routing tables converged to prevent dead routes from being advertised across boundaries.
C. Once a route is received on an interface, advertise that route as unreachable back out the same interface.
D. Information about a route should never be sent back in the direction from which the original update came.
A. IGRP
B. CDP
C. OSPF
D. RIP v1
E. RIP v2
F. EIGRP
A. Router(config-router)# network 192.168.10.0 0.0.0.255 0
B. Router(config-router)# network 192.168.10.0 0.0.0.255 area 0
C. Router(config-router)# network 192.168.10.0 255.255.255.0 area 0
D. Router(config)# router ospf 0
E. Router(config)# router ospf 1
A. Allows interfaces to share common IP addresses.
B. Allows an interface to remain up without the aid of keepalives.
C. Allows a router to send routing and not receive updates via that interface.
D. Allows a routing protocol to forward updates that is missing its IP address.
E. Allows a router to receive routing updates on an interface but not send updates via that interface.
A. Spanning Tree Protocol
B. Shortest path first tree
C. Link-state advertisements (LSA)
D. Hold-down timers
E. Split horizon
F. VRRP
最新試題
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()
Which connections allow the use of full-duplex Ethernet?()
What is a global command?()
What is the subnetwork address for a host with IP address 201.100.5.68/28?()
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?()
What does a configuration Register Setting of 0x2105 indicate to the Router? ()
Which of the following if addresses can be assigned to host devices?()
A router with a serial interface will be used for an ISDN link.What other function group devices are required to complete the connection to the service provider? ()
Identify three valid host addresses in the 192.168.27.0 network with a subnet mask of 255.255.255.240. ()
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? ()