A. You can delete individual statements in a named access list
B. Named access lists require a numbered range from 1000 to 1099.
C. Named access lists must be specified as standard or extended.
D. You can use the ip access-list command to create named access lists.
E. You cannot delete individual statements in a named access list.
F. You can use the ip name-group command to apply named access lists.
您可能感興趣的試卷
你可能感興趣的試題
A. access-list 15 deny telnet any 10.10.1.0 0.0.0.255 eq 23
B. access-list 115 deny udp any 10.10.1.0 eq telnet
C. access-list 15 deny tcp 10.10.1.0 255.255.255.0 eq telnet
D. access-list 115 deny tcp any 10.10.1.0 0.0.0.255 eq 23
E. access-list 15 deny udp any 10.10.1.0 255.255.255.0 eq 23
A. access-list 101 permit tcp any 172.17.18.252 0.0.0.0 eq 80
B. access-list 1 permit tcp any 172.17.17.252 0.0.0.0 eq 23
C. access-list 101 permit tcp 172.17.17.252 0.0.0.0 any eq 23
D. access-list 101 deny tcp any 172.17.17.252 0.0.0.0 eq 23
E. access-list 101 deny tcp any 172.17.18.252 0.0.0.0 eq 80
F. access-list 101 permit tcp any 172.17.17.252 0.0.0.0 eq 23
A. ACLs monitor the number of bytes and packets.
B. Virus detection.
C. ACLs dentify interesting traffic for DDR.
D. ACLs provide IP route filtering.
E. ACLs provide high network availability.
F. ACLs classify and organize network traffic.
A. Before they are routed to an outbound interface.
B. After they are routed for outbound traffic.
C. After they are routed to an outbound interface while queuing.
D. Before and after they are routed to an outbound interface.
E. Depends on the configuration of the interface
F. None of the above
A. To configure a route to the first Layer 3 device on the network segment.
B. To configure a route from an ISP router into a corporate network.
C. To configure a route when the administrative distance of the current routing protocolis too low.
D. To reach a network is more than 15 hops away.
E. To provide access to the Internet for enterprise hosts.
A. router(config)# ip route 0.0.0.0 10.1.1.0 10.1.1.1
B. router(config)# ip default-route 10.1.1.0
C. router(config)# ip default-gateway 10.1.1.0
D. router(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
A.
B.
C.
D.
E.
F.
A. It is globally enabled by default on Cisco routers.
B. It is globally enabled by default on all routers.
C. It is a proprietary protocol.
D. It is a non-proprietary protocol.
E. It can be used to gather hardware and protocol information about neighbor devices.
A. The Frame Relay encapsulation on the physical interface.
B. The local DLCI on each subinterface.
C. An IP address on the physical interface.
D. The subinterface type as point-to-point.
A.close
B.disable
C.disconnect
D.suspend
E.exit
F.None of the above
最新試題
What does a configuration Register Setting of 0x2105 indicate to the Router? ()
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? ()
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? ()
How many usable sub network and usable hosts per subnet result in the network address 201.105.13.0 is sub netted with a mask of /26? ()
Which characteristics are representative of a link-state routing protocol?()
Which connections allow the use of full-duplex Ethernet?()
Which command is used to display the placement and direction of an IP access control list on a router?()
Which of the following options lists the steps in PPP session establishment in the correct order?()
Which of the following host addresses are member of networks that can be routed across the public Internet? ()
Which statement describes the rule of split horizon?()