You are working as a network technician, study the exhibit carefully. Your boss has informed youthat there have been problems with the WAN that is using EIGRP routing protocol. You arerequired to troubleshoot these problems.
Before going to the questions of this sim, we should have a quick review about GRE tunneling:GRE Quick Summary.
The picture below shows how to configure a GRE Tunnel between two routers, notice that the"tunnel destination" must be the IP address of the interface, not of the opposite tunnel.
Notice: The tunnel source on one router must be specified as the tunnel destination on the otherrouter.
Below are the questions of this lab-sim.
What is the reason that tunnel 5 on the HQ router is down when its companion tunnel on theBranch5 router is up?()
A.The IP address on the tunnel interface on Branch5 is incorrect. It should be 192.168.1.16255.255.255.252
B.The tunnel source for tunnel 5 is incorrect on the HQ router. It should be serial 2/0
C.The tunnel numbers for tunnel between the HQ router and the Branch5 router do not match
D.The tunnel destination address for tunnel 5 is incorrect on the HQ router. It should be 10.2.5.1to match the interface address of the Branch5 router
E.The tunnel interface for tunnel 5 on the HQ router is in the administrative down state
您可能感興趣的試卷
你可能感興趣的試題
You are working as a network technician, study the exhibit carefully. Your boss has informed youthat there have been problems with the WAN that is using EIGRP routing protocol. You arerequired to troubleshoot these problems.
Before going to the questions of this sim, we should have a quick review about GRE tunneling:GRE Quick Summary The picture below shows how to configure a GRE Tunnel between tworouters, notice that the "tunnel destination" must be the IP address of the interface, not of theopposite tunnel.
Notice: The tunnel source on one router must be specified as the tunnel destination on the otherrouter.
Below are the questions of this lab-sim.
What is preventing the 192.168.1.150 network from appearing in the HQ router’s routing table?()
A.The default route is missing from the Branch4 router
B.The IP address on the E0/0 interface for the Branch4 router has the wrong IP mask. It shouldbe 255.255.255.252
C.The network statement under router EIGRP on the Branch4 router is incorrect. It should benetwork 192.168.1.0 0.0.0.255.
D.When running EIGRP over GRE tunnels, you must manually configure the neighbor addressusing the eigrp neighbor ipaddress command.
E.The IP address on the tunnel interface on P4S-Branch4 is incorrect. It should be 192.168.1.12255.255.255.252
A.timezone EST -5
B.clock timezone GMT -5
C.dock GMT -5
D.clock EST-5
E.NTP timezone EST -5
F.dock timezone EST -5
A.Mismatched EtherChannel protocol
B.Mismatched EtherChannel port selection
C.Mismatched EtherChannel distribution algorithm
D.Mismatched trunk mode
E.Mismatched native VLAN
F.Mismatched link speed
A.NAT mapping
B.NAT overloading
C.NAT caching
D.Static NAT
E.Dynamic NAT
F.Overlapping NAT
A.The network is load balancing among different members of the VRRP group
B.The default hello timers are 1 second
C.The interface IP address is being used as the virtual IP address
D.There are several routers in the group simultaneously forwarding traffic for the group
E.It is a Cisco Proprietary protocol
F.The default hello timers are 3 seconds
A.A routed port does not run STP or DTP
B.A routed port is considered to be in a down state if it is not operational at both Layer 1 andLayer 2
C.An SVI is considered to be in a down state if it is not operational at both Layer 1 and Layer 2
D.An SVI is considered to be in a down state only when none of the ports in the correspondingVLAN are active
E.An SVI port does not run 5TP or DTP
F.To create a trunk, an SVI can be logically divided into subinterfaces
A.The interface you configured for AutoQoS is set to half-duplex
B.AutoQoS was configured on only one end of the link
C.The interface you configured for AutoQoS has no IP address
D.The interface’s bandwidth is not correctly configured
E.CEF is not enabled on the interface
F.You enabled AutoQoS on the interface but forgot to enable globally first
A.Spanning Tree Protocol
B.Cabling
C.Frame forwarding
D.Packet forwarding
E.EtherChannel
F.Routing protocols
A.Building schematic
B.IGP community elements
C.Listing of interconnections
D.Physical topology diagram
E.Logical topology diagram
F.Inventory of network equipment
A.An error will result because a router cannot be configured with an EIGRP variance of 3 becausethe maximum variance number is 2
B.The successor route will end up in the routing table, and so will any route with a metric at mostthree times greater than the value of the successor’s metric
C.EIGRP will only advertise routes that are within three hops of the current router
D.The successor route will end up in the routing table, and so will any route with a metric at leastone third the value of the successor’s metric
E.The best three routes with equal cost paths will end up in the routing table
F.The successor route will be any route with three times the value of the advertised distance
最新試題
Which statement correctly describes IPsec VPN backup technology?()
As a network engineer, do you know for what purpose SDM uses Security Device Event Exchange(SDEE)?()
Which statement about PPPoA configuration is correct?()
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec, which two parameters are required when defining the tunnel interfaceinformation?()
A new router was configured with the following commands:The configuration above was found on an Internet Service Provider’s (ISP) Multiprotocol LabelSwitching (MPLS) network. What is its purpose?()
Drag the DSL local loop topic on the left to the correct descriptions on the right.
Refer to the exhibit. Which two statements about the AAA configuration are true?()
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.