A.Ping 10.1.1.1 Data Pattern M
B.Ping 10.1.1.1 timeout 0
C.Ping 10.1.1.1 size 1500 df-bit
D.Ping 10.1.1.1 source loopback 0
E.Ping 10.1.1.1 size 1500
F.Ping 10.1.1.1 size 1500 Strict
您可能感興趣的試卷
你可能感興趣的試題
A.RIP route 10.1.2.0/24
B.EIGRP route 10.1.2.0/24
C.RIP route 10.1.0.0/16
D.OSPF route 10.1.0.0/16
E.RIP route 10.0.0.0/16
F.OSPF route 10.1.2.0/24
A.OSPF topology table
B.OSPF interface table
C.OSPF routing information base
D.OSPF link-state database
E.OSPF adjacency table
F.OSPF neighbor table
A.Problem report
B.Problem collaboration
C.Problem diagnosis
D.Problem resolution
E.Problem documentation
F.Probiem authentication
A.0000.0c70.ac22
B.0000.0c07.22ac
C.0000.0c07.acl6
D.0000.0c07.ac22
E.0000.0c70.cala
F.0000.0d22.ac07
A.Eliminate potential causes
B.Collect information
C.Document causes
D.Hypothesize underlying causes
E.Verif/ hypothesis
F.Examine collected information
A.The adjacency table is populated from a router’s ARP cache
B.CEF does not require the first packet of a data flow to be process switched
C.CEF maintains the Forward Information Base and the adjacency table
D.CEF can be enabled with the interface command ip cef
E.The FIB is populated from a router’s IP routing table
F.On most router platforms CEF is enabled by default
A.CEF switching is disabled on the switch
B.The source device and destination device are in different VLANs
C.The VLAN is excluded from the trunk
D.The host is connected to the switch through an IP phone
E.A faulty cable from host to switch or between switches
F.The trunking encapsulation type is inconsistent on the two ends of the link
A.Cisco Express Fonvarding
B.FIB switching
C.Cache switching
D.Optimized switching
E.Process switching
F.Fast switching
A.Fault management
B.Accounting management
C.Operations management
D.Performance management
E.Security management
F.Configuration management
A.sh ip route
B.sh ip cef 〈ip_address〉
C.sh adjacency 〈ip_address〉
D.sh ip route 〈ip_addres$〉
E.sh ip adjacency 〈/p_address〉
F.sh ip cef 〈mac_addrQss〉〈ip_address〉
最新試題
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN?()
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete?()
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password?()
Drag and drop question. The upper gives the MPLS functions, the bottom describes the planes.Drag the above items to the proper location at the below
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
Network Topology Exhibit:Configuration Exhibit:NET(config)# access-list 112 deny icmp any any echo logNET(config)# access-list 112 deny imp any any redirect logNET(config)# access-list 112 deny icmp any any mask-request logNET(config)# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET(config)# interface Fa0/1NET(config-if)# ip access-group 112 inYou work as a network administrator at networkTut.com, study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However, the configurationis incorrect. On the basis of the information in the exhibit, which configuration option wouldcorrectly configure router NET?()
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec, which two parameters are required when defining the tunnel interfaceinformation?()
Drag the IPsec protocol description from the above to the correct protocol type on the below.(Notall descriptions will be used)Drag and Drop question, drag each item to its proper location.