A.Route reflectors
B.Route maps
C.Route redistribution
D.Peer groups
E.Aggregate addresses
您可能感興趣的試卷
你可能感興趣的試題
A.Configure weight
B.Enable route reflector
C.Create a distribute list
D.Enable the Longer Autonomous System path option
E.All of the above
A.Router （config-router）#network 154.2.1.0
B.outer （config-router）#network 164.2.1.0
C.Router （config-router）#network-advertise 154.2.1.0
D.Router （config-router）#network 154.2.1.0 mask 255.255.255.0
E.None of the other alternatives apply
The BGP routing table consists of the following network routes：
What is the correct command to summarize these prefixes into a single summary prefix of192.168.12.0/22 while also allowing for the advertisement of the more specific prefixes？（）
A.network 192.168.12.0 mask 255.255.252.0
B.network 192.168.12.0 mask 0.0.3.255
C.network 192.168.12.0
D.aggregate-address 192.168.12.0 255.255.252.0
E.aggregate-address 192.168.12.0 255.255.252.0 summary-only
F.aggregate-address 192.168.12.0 255.255.252.0 as-set
A.A peer router running IBGP
B.A peer router running EBGP
C.A community member running IBGP
D.A peer group member running IBGP
E.A peer group member running EBGP
A BGP router is configured as shown below：
interface ethernet 0
ip address 10.10.10.1 255.255.0.0!
int serial 0
ip address 172.16.1.1 255.255.255.252!
router bgp 65001
neighbor 192.168.1.1 remote-as 65002
Based on the above configuration， which of the following BGP statements would inject the10.10.0.0/16 prefix into the BGP routing table？（）
A.network 10.0.0.0
B.network 10.10.0.0 mask 255.255.0.0
C.network 10.10.10.1 mask 255.255.255.255
D.network 10.10.10.0 mask 255.255.255.0
E.network 10.0.0.0 mask 255.255.0.0
A.The IBGP routers must always be fully meshed
B.The IBGP routers can be in a different AS
C.The IBGP routers must be directly connected
D.The IBGP routers do not need to be directly connected
E.None of the other alternatives apply are true
The network consists of two separate autonomous systems as shown below：
You need to configure Router R2 as a BGP route reflector and Router R1 as the client. Assumingthat Router R3 isn’t running BGP， which two of the commands below would you enter on R2 tosatisfy your goals？（）
A.neighbor 165.50.12.1 remote-as 65100
B.neighbor 165.50.12.2 remote-as 64000
C.neighbor 165.50.12.1 route-reflector-client
D.neighbor 165.50.12.2 route reflector-client
Refer to the exhibit. All routers are configured for BGP. EBGP routes received on router R2 showup in the BGP table on routers R1 and R3 but not in their IP routing tables. What would causethis？（）
A.EBGP multihop is not configured on routers R1 and R3
B.Routers R1 and R3 do not receive the same routes via an IGP
C.Synchronization in autonomous system 100 is turned is on
D.The BGP routers in autonomous system 100 are not logically fully-meshed
E.Synchronization in autonomous system 100 is turned is off
A.When traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose2 because of the higher MED value of SanJose2
B.The serial 0/0/1 interface on the ISP router has been configured with the set metric 50command
C.The output was generated by entering the show ip bgp command on the SanJose1 router
D.The output was generated by entering the show ip bgp command on the ISP router
E.The serial 0/0/1 interface on the ISP router has been configured with the set metric 75command
F.When traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose1 because of the lower MED value of SanJose1
Refer to the exhibit. Router RT3 discovers network 202.176.56.0 via BGP. Which one of thesestatements is true？（）
A.RT1 advertised network 202.176.50.0/24 with a metric of 782
B.RT3 is directly connected to RT1 using subnet 192.168.1.0
C.RT3 has an IGP metric of 782 to reach 192.168.1.1
D.RT3 has a BGP metric of 782 to reach 192.168.1.1
E.RT1 advertised network 202.176.50.0/24 with a metric of 1000
F.RT3 has an IGP metric of 1782 to reach 202.176.56.0/24
最新試題
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
Study the exhibit carefully.Routers A and B are customer routers. Routers 1， 2， 3 and 4 are provider routers. The routers areoperating with various IOS versions. Which frame mode MPLS configuration statement is true？（）
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）