A. An IPv6 address is 64 b long and is represented as hexadecimal characters.
B. An IPv6 address is 32 b long and is represented as decimal digits.
C. An IPv6 address is 128 b long and is represented as decimal digits.
D. An IPv6 address is 128 b long and is represented as hexadecimal characters.
您可能感興趣的試卷
你可能感興趣的試題
A. The new IOS image is too large for the router flash memory.
B. The TFTP server is unreachable from the router.
C. The new IOS image is not correct for this router platform.
D. The IOS image on the TFTP server is corrupt.
E. There is not enough disk space on the TFTP server for the IOS image.
This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? （）
A. ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco
B. Remote27(config)# line console 0 Remote27(config-line)# login Remote27(config-line)# password cisco
C. ACCESS1(config)# line vty 0 4 ACCESS1(config-line)# login ACCESS1(config-line)# password cisco
D. Remote27(config)# line vty 0 4 Remote27(config-line)# login Remote27(config-line)# password cisco
E. ACCESS1(config)# enable password cisco
F. Remote27(config)# enable password cisco
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.
A. 24
B. 4
C. 3
D. 16
A. The Gallant router has the wrong LMI type configured
B. Inverse ARP is providing the wrong PVC information to the Gallant router
C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E. The IP address on the serial interface of the Attalla router is configured incorrectly
A. point-to-point
B. broadcast multi-access
C. nonbroadcast multi-access
D. nonbroadcast multipoint
E. broadcast point-to-multipoint
A. permit all packets matching the first three octets of the source address to all destinations
B. permit all packet matching the last octet of the destination address and accept all source addresses
C. permit all packet matching the host bits in the source address to all destinations
D. permit all packet from the third subnet of the network address to all destinations
A. FTP traffic from 192.169.1.22 will be denied
B. No traffic, except for FTP traffic will be allowed to exit E0
C. FTP traffic from 192.169.1.9 to any host will be denied
D. All traffic exiting E0 will be denied
E. All FTP traffic to network 192.169.1.9/29 will be denied
A. access-list 101 in
B. access-list 101 out
C. ip access-group 101 in
D. ip access-group 101 out
最新試題
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）
At which layer of the OSI model is RSTP used to prevent loops?（）
Three access ports have been installed and configured to a small office.What term defines the wireless topology?（）
At which layer of the OSI model dose PPP perform?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
On which options are standard access list based?（）
How are VTP advertisements delivered to switches across the network?（）
What is the default administrative distance of OSPF?（）
What is the purpose of the cisco Vlan Trunking protocol?（）
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?（）