Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement
HSRP has been configurationured between DSW1 and DSW2. DSW1 is configurationured to be activerouter but it never becomes active even though the HSRP communication between DSW1 and DSW2 isworking.
Configuration on DSW1
CertKiller.com
track 1 ip route 10.1.21.128 255.255.0.0 metric threshold threshold metric up 1 down 2!
track 10 ip route 10.2.21.128 255.255.255.0 metric threshold threshold metric up 63 down 64!
interface Vlan10
ip address 10.2.1.1 255.255.255.0
standby 10 ip 10.2.1.254
standby 10 priority 200
standby 10 preempt
standby 10 track 1 decrement 60
Configuration on R4
Cisco 642-832： Practice Examinterface loopback0
ip address 10.2.21.128 255.255.255.0
On which device is the fault condition located？（）
A.R4
B.DSW2
C.DSW1
D.R3
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement：
Client 1 is able to ping 10.1.1.2 but not 10.1.1.1. Initial troubleshooting shows that R1 does not have anyOSPF neighbors or any OSPF routes
Configuration on R1：
router ospf 1
CertKiller.com
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12
default-information originate always!
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.1 255.255.255.252
ip nat inside
ip ospf message-digest-key 1 md5 TSHOOT
Configuration on R2：
router ospf 1
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12!
Cisco 642-832： Practice Exam
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.2 255.255.255.252
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 TSHOOT
What is the solution of the fault condition？（）
A.ipospf authentication message-digestcommand has to be added on S0/0/0/0.12
B.ipospf authentication message-digestcommand has to be added under the OSPF routing process
C.A static route to 10.1.1.4 must be added on R1
D.ipnat outside must be added on S0/0/0/0.12
A.Physical
B.Session
C.Application
D.Data-Link
E.Network
The following command is issued on a Cisco Router：
Router（configuration）#logging console warnings
Which alerts will be seen on the console？（）
A.Warnings only
B.debugging， informational， notifications， warnings
C.warnings， errors， critical， alerts， emergencies
D.notifications， warnings， errors
E.warnings， errors， critical， alerts
A.ntp server 10.1.1.1 ntp server 10.1.1.2
B.ntp server 10.1.1.1 ntp server 10.1.1.2 primary
C.ntp server 10.1.1.1 ntp server 10.1.1.2 prefer
D.ntp server 10.1.1.1 fallback ntp server 10.1.1.2
What level of logging is enabled on a Router where the following logs are seen？（）
A.alerts
B.critical
C.errors
D.notifications
The following commands are issued on a Cisco Router：
What will the debug output on the console show？（）
A.All IP packets passing through the router
B.Only IP packets with the source address of 10.1.1.1
C.All IP packets from 10.1.1.1 to 172.16.1.1
D.All IP Packets between 10.1.1.1 and 172.16.1.1
最新試題
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
Drag the DSL local loop topic on the left to the correct descriptions on the right.
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Drag and drop each management protocol on the above to the correct category on the below.
Which statement correctly describes IPsec VPN backup technology？（）
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.