A. can be used over analog circuits
B. maps Layer 2 to Layer 3 address
C. encapsulates several routed protocols
D. supports IP only
E. provides error correction
您可能感興趣的試卷
你可能感興趣的試題
A. Administratively shut down the interfaces.
B. Physically secure the interfaces.
C. Configure a virtual terminal password and login process.
D. Enter an access list and apply it to the terminal interfaces using the access-class command.
E. Create an access list and apply it to the terminal interfaces using the access-group command.
A.multicast
B.broadcast
C.allcast
D.podcast
E.anycast
A.blocking
B.learning
C.disabled
D.forwarding
E.listening
A. Security increases because only the network administrator may change the routing tables.
B. Configuration complexity decreases as network size increases.
C. Routing updates are automatically sent to neighbors.
D. Route summarization iscompued automatically by the router.
E. Routing traffic load is reduced when used in stub network links
F. An efficient algorithm is used to build routing tables,using automatic updates.
G. Routing tables adapt automatically to topology changes.
A. to confine network instability to single areas of the network.
B. to reduce the complexity of router configuration
C. to speed up convergence
D. to lower costs by replacing routers with distribution layer switches
E. to decrease latency by increasing bandwidth
F. to reduce routing overhead
A.complicated header
B.plug-and-play
C.no broadcasts
D.checksums
E.optional IPsec
F.autoconfiguration
A. They are always present in the NAT table.
B. They allow connection to be initiated from the outside.
C. They can be configured with access lists, to allow two or more connections to be initiated from the outside.
D. They require no inside or outside interface markings because addresses are statically defined.
A. RSTP significantly reduces topology reconverging time after a link failure.
B. RSTP expends the STP port roles by adding the alternate and backup roles.
C. RSTP port atates are blocking,discarding,learing,or forwarding.
D. RSTP also uses the STP proprsal-agreement sequence.
E. RSTP use the same timer-baseed process as STP on point-to-point links.
F. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
A. NAT protects network security because private networks are not advertised.
B. NAT accelerates the routing process because no modifications are made on the packets.
C. Dynamic NAT facilitates connections from the outside of the network.
D. NAT facilitates end-to-end communication when IPsec is enable.
E. NAT eliminates the need to re-address all host that require extemal access.
F. NAT conserves addresses through host MAC-level multiplexing.
A. SW1#show swithport port-security interface FastEthernet 0/12
B. SW1# show swithport port-secure interface FastEthernet 0/12
C. SW1# show port-secure interface FastEthernet 0/12
D. SW1#show running-config
E. SW1#show port-security interface FastEthernet 0/12
最新試題
What is the default administrative distance of OSPF?()
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?()Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
Which command encrypts all plaintext passwords?()
A router receives information about network 192.168.10.0/24 from multiple sources.What will the router consider the most reliable information about the path to that network?()
Which pairing reflects a correct protocol-and-metric relationship?()
Which address is the IPV6 all-RIP-routers muticast group address that is used by RIPng as the destaion address?()
Which IPsec security protocol should be used when confidentiality is required?()
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()
A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?()
Three access ports have been installed and configured to a small office.What term defines the wireless topology?()