A. perform flow lookups
B. intercept packets on service enabled ports
C. run packets through the vPath flow manager
D. classify the packets
E. flow manager emits an action for the packets
F. enforce the action determined by the flow manager
您可能感興趣的試卷
你可能感興趣的試題
Given the following configuration， what command can be used to determine the physical path that traffic will be sent out upon？（）
Port-profile type Ethernet name vm-data
Switchport mode trunk
Switchport trunk allowed vlan 200-210
Channel-group auto mode on mac-pinning
State enabled
Vmware port-group
No shut
Port-profile type vethernet name vlan-200
Switchport mode access Switchport vlan 200
State enabled Vmware port-group No shut
A. module vem X execute vemcmd show trunk
B. show module 3 internal pinning
C. module vem X execute vemcmd show port
D. show module vem mapping
E. show interface vethX pinning
A. Upstream switch
B. Virtual Supervisor Module
C. VMware distributed switch
D. VMware vSwitch
E. Service virtual machine
A. All vEthernet ports are trusted， and all Ethernet ports such as uplinks and port channels are trusted.
B. All vEthernet ports are not trusted， and all Ethernet ports such as uplinks and port channels are not trusted.
C. All vEthernet ports are trusted and all Ethernet ports such as uplinks and port channels are not trusted.
D. All vEthernet ports are not trusted and all Ethernet ports such as uplinks and port channels are trusted.
n1kv-l3（config）# show lacp offload status
Current Status ： Enabled
Running Config Status ： Enabled
Saved Config Status ： Disabled
What two facts does the output signify？ （）
A. LACP is enabled on the Nexus 1000v.
B. LACP will be offloaded to the upstream switch.
C. LACP will be negotiated to the VM.
D. LACP is negotiated by the VSM.
E. LACP is negotiated by the VEM in all instances.
A. intelligent traffic steering to the VSG
B. offloading the processing from the VSG to the VEM
C. intelligent traffic steering to the VNMC
D. offloading the processing from the VSG to the flow manager
E. deep packet inspection
A. channel-group auto mode on
B. channel-group auto mode active
C. channel-group auto mode on sub-group cdp
D. channel-group auto mode on sub-group manual
E. channel-group auto mode on mac-pinning
A. accounting
B. authentication
C. authorization
D. network monitoring
E. network planning
A. 0
B. 1
C. 2
D. 3
E. 4
F. 5
When configuring vPC-HM CDP with multiple links to the same switch， are port-channels required？（）
A. Each link between the upstream switch and the VEM is an individual subgroup.
B. Connections that go to the same upstream switch must be configured with the command channel-group
C. Connections that go to the same upstream switch must be configured with the command channel-group
D. With vPC-HM CDP， the user can pin traffic from a specific VM to a specific uplink.
E. Connections that go to the same upstream switch must be configured with the command channel-group
A. 0
B. 1
C. 2
D. 3
E. 4
最新試題
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true？ （）
Which of the following are supported in Cisco Global Site Selector？ （）
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
When testing ICMP access to a functional load-balancing ACE VIP， it fails. What is the reason of this problem？ （）
In the event of a GSS failure in a GSS cluster， which is true？（）