A.learning
B.listening
C.discarding
D.forwarding
您可能感興趣的試卷
你可能感興趣的試題
A.HostA is not on the same subnet as its default gateway
B.The address of SwitchA is a subnet address
C.The Fa0/0 interface on RouterA is on a subnet that cannot be used
D.The serial interfaces of the routers are not on the same subnet
E.The Fa0/0 interface on RouterB is using a broadcast address
Refer to the exhibit。A problem with network connectivity has been observed.It is suspected that the cable connected to switch port Fa0/9 on Switch 1 disconnected.What would be an effect of tis cable being disconnected?()
A.Host B would not be able to access the server in VLAN9 until the cable is reconnected
B.For less than a minute ,Host B would not be able to access the server in VLAN9.Then normal network function would resume.
C.Communication between VLAN3 and the other VLANs would be disabled
D.The transfer of files from Host B to the server in VLAN9 would be significantly slower.
Refer to the exhibit. The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? ()
A.Configure the gateway on Host A as 10.1.1.1.
B.Configure the gateway on Host B as 10.1.2.254.
C.Configure the IP address of Host A as 10.1.2.2.
D.Configure the IP address of Host B as 10.1.2.2.
E.Configure the masks on both hosts to be 255.255.255.224.
F.Configure the masks on both hosts to be 255.255.255.240.
Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem?()
A.All of the routers need to be configured for backbone Area 1.
B.R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C.A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D.The hello and dead interval timers are not set to the same values on R1 and R3.
E.EIGRP is also configured on these routers with a lower administrative distance.
F.R1 and R3 are configured in different areas.
A.Router# show ip eigrp adjacency
B.Router# show ip eigrp topology
C.Router# show ip eigrp interfaces
D.Router# show ip eigrp neighbors
A.The command is accepted and the respective VLAN is added to vlan dat.
B.The command is rejected.
C.The command is accepted and you must configure the VLAN manually.
D.The port turns amber.
A.after broken links are re-established
B.in an improperly implemented redundant topology
C.when upper-layer protocols require high reliability
D.during high traffic periods
E.when a dual ring topology is in use
A.ping
B.tracert
C.ipconfig
D.show ip route
E.winipcfg
F.show interfaces
Refer to the exibit .An attempt to deny web access to a subnet blocks all traffic from the subnet.Which interface command immedicately removes the effect of ACL 102?()
A.no ip access-group 102 in
B.no ip access-group 102 out
C.no ip access-list 102 in
D.no ip access-class 102 out
E.no ip access-class 102 in
A.Addresses in a private range will be not routed on the Internet backbone.
B.Only the ISP router will have the capability to access the public network.
C.The NAT process will be used to translate this address in a valid IP address.
D.Several automated methods will be necessary on the private network.
E.A conflict of IP addresses happens, because other public routers can use the same range.
最新試題
What command visualizes the general NetFlow data on the command line?()
What are two enhancements that OSPFv3 supports over OSPFv2? ()
What level will be trapped if the administrator executes the command ?()
Refer to the exhibit.If the devices produced the given output,what is the cause of the EtherChannel problem?()
What are the benefit of using Netflow?()
A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? ()
What is the default Syslog facility level?()
What are three reasons to collect Netflow data on a company network?()
What are two benefits of using a single OSPF area network design?()
What OSPF command, when configured, will include all interfaces into area 0?()