A.Addresses in a private range will be not routed on the Internet backbone.
B.Only the ISP router will have the capability to access the public network.
C.The NAT process will be used to translate this address in a valid IP address.
D.Several automated methods will be necessary on the private network.
E.A conflict of IP addresses happens, because other public routers can use the same range.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Give this output for SwitchC, what should the network administrator's next action be?()
A.Check the trunk encapsulation mode for SwitchC's fa0/1 port.
B.Check the duplex mode for SwitchC's fa0/1 port.
C.Check the duplex mode for SwitchA's fa0/2 port.
D.Check the trunk encapsulation mode for SwitchA's fa0/2 port.
Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?()
A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.
A.802.1Q giants frames could saturate the link.
B.VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C.A native VLAN mismatch error message will appear.
D.VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.
A.Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.
B.Router C will use ICMP to inform Router B that Host 2 cannot be reached.
C.Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.
D.Router C will send a Destination Unreachable message type.
E.Router C will send a Router Selection message type.
F.Router C will send a Source Quench message type.
A.show ip access-list
B.show access-list
C.list ip interface
D.show interface
E.show ip interface
A.BackboneFast
B.UplinkFast
C.Root Guard
D.BPDU Guard
E.BPDU Filter
A.The process id is configured improperly
B.The OSPF area is configured improperly
C.The network wildcard mask is configured improperly
D.The network number is configured improperly
E.The AS is configured improperly
F.The network subnet mask is configuerd improperly
Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network.The network administrator connected to console port,issued the show ip route command,and was able to ping the server.Based on the output of the show ip route command topology shown in the graphic,what is the cause of the failure?()
A.IP routing is not enabled
B.A static route is configured incorrectly
C.The network has not fully converged
D.The FastEthernet interface on Coffee is disabled
E.The routing table on Coffee has not updated
F.The neighbor relationship table is not correctly updated
A.Add two more FastEthernet interfaces.
B.Add a second router to handle the vlan traffic.
C.Use a hub to connect the four vlans with a FastEthernet interface on router.
D.Implement a router-on-a-stick configuration.
Refer to the exhibit a network administrator cannot establish a telnet session with the indicated router at is the cause of this failure?()
A .A level 5 password is not set
B.The vty password is missing
C.The console password is missing
D.An ACL is blocking Telnet access
最新試題
What are three reasons to collect Netflow data on a company network?()
What parameter can be different on ports within an EtherChannel?()
What OSPF command, when configured, will include all interfaces into area 0?()
What are two benefits of using a single OSPF area network design?()
Which is true about OSPF router-id?()
What are the Popular destinations for syslog messages to be saved? ()
Which three statements about the features of SNMPv2 and SNMPv3 are true?()
A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? ()
What are three values that must be the same within a sequence of packets for Netflow to consider them a network flow?()
What command instructs the device to timestamp Syslog debug messages in milliseconds?()