Refer to the exhibit. Give this output for SwitchC, what should the network administrator's next action be?()
A.Check the trunk encapsulation mode for SwitchC's fa0/1 port.
B.Check the duplex mode for SwitchC's fa0/1 port.
C.Check the duplex mode for SwitchA's fa0/2 port.
D.Check the trunk encapsulation mode for SwitchA's fa0/2 port.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?()
A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.
A.802.1Q giants frames could saturate the link.
B.VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C.A native VLAN mismatch error message will appear.
D.VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.
A.Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.
B.Router C will use ICMP to inform Router B that Host 2 cannot be reached.
C.Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.
D.Router C will send a Destination Unreachable message type.
E.Router C will send a Router Selection message type.
F.Router C will send a Source Quench message type.
A.show ip access-list
B.show access-list
C.list ip interface
D.show interface
E.show ip interface
A.BackboneFast
B.UplinkFast
C.Root Guard
D.BPDU Guard
E.BPDU Filter
A.The process id is configured improperly
B.The OSPF area is configured improperly
C.The network wildcard mask is configured improperly
D.The network number is configured improperly
E.The AS is configured improperly
F.The network subnet mask is configuerd improperly
Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network.The network administrator connected to console port,issued the show ip route command,and was able to ping the server.Based on the output of the show ip route command topology shown in the graphic,what is the cause of the failure?()
A.IP routing is not enabled
B.A static route is configured incorrectly
C.The network has not fully converged
D.The FastEthernet interface on Coffee is disabled
E.The routing table on Coffee has not updated
F.The neighbor relationship table is not correctly updated
A.Add two more FastEthernet interfaces.
B.Add a second router to handle the vlan traffic.
C.Use a hub to connect the four vlans with a FastEthernet interface on router.
D.Implement a router-on-a-stick configuration.
Refer to the exhibit a network administrator cannot establish a telnet session with the indicated router at is the cause of this failure?()
A .A level 5 password is not set
B.The vty password is missing
C.The console password is missing
D.An ACL is blocking Telnet access
A.As numbers must be changed to match on all the routers.
B.Loopback interface must be configured so a DR is elected.
C.The no auto-summary command is needed on Router A and Router C.
D.Router B needs to have two network statements, one for each connected network.
最新試題
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?()
What command instructs the device to timestamp Syslog debug messages in milliseconds?()
Which three statements about Syslog utilization are true?()
In a GLBP network, who is responsible for the arp request?()
What Netflow component can be applied to an interface to track IPv4 traffic?()
In GLBP, which router will respond to client ARP requests?()
What are two benefits of using a single OSPF area network design?()
What authentication type is used by SNMPv2?()
What are three reasons to collect Netflow data on a company network?()
What OSPF command, when configured, will include all interfaces into area 0?()