S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally， static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes？（）
A.Configure the no ip subnet-zero command on R1,R2,and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
您可能感興趣的試卷
你可能感興趣的試題
Which destination addresses will be used by Host A to send data to Host C？（）
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router’s E0 interface
F. the MAC address of the router’s E0 interface
An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem，the administrator views the output of the show vtp status command， which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database？（）
A. Switch（config-if）# switchport access vlan 50
B. Switch（vlan）# vtp server
C. Switch（config）# config-revision 20
D. Switch（config）# vlan 50 name Tech
E. Switch（vlan）# vlan 50
F. Switch（vlan）# switchport trunk vlan 50
A.10.188.31.0/27
B.10.188.31.0/26
C.10.188.31.0/29
D.10.188.31.0/28
E.10.188.31.0/25
Refer to the exhibit.A network technician is asked to design a small network with redundancy. The exhibit represents this design， with all hosts configured in the same VLAN. What conclusions can be made about this design？（）
A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.
A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2.
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
Refer to the exhibit.After a RIP route is marked invalid on Router_1， how much time will elapse before that route is removed from the routing table？（）
A.30 seconds
B.60 seconds
C.90 seconds
D.180 seconds
E.240 seconds
A.proxy
B.dual-stack
C.tunneling
D.dot1q
A.user EXEC mode
B.global configuration mode
C.privileged EXEC mode
D.auxiliary setup mode
A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
最新試題
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么？（）
PC 無法連接到任何遠程網站，無法ping 通其默認網關，也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常？（）
請參見圖示。從主機X 發出的到主機Y 的tracert 命令已成功。下列哪一項正確地反映了追蹤列表中顯示的中間網絡設備的順序？（）
在路由器上使用Router#copy running-config startup-config 命令會產生什么效果？（）
在配置路由器時，網絡技術人員想要命名路由器。輸入hostname 命令后，技術人員會看到下列哪一項提示？（）
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確？（）
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2？（）
在Cisco IOS 設備中，啟動配置文件存儲于何處？（）
請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置？（）
以下哪兩種介質可提供高達1Gb/s 的帶寬？（）