Which destination addresses will be used by Host A to send data to Host C？（）
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router’s E0 interface
F. the MAC address of the router’s E0 interface
您可能感興趣的試卷
你可能感興趣的試題
An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem，the administrator views the output of the show vtp status command， which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database？（）
A. Switch（config-if）# switchport access vlan 50
B. Switch（vlan）# vtp server
C. Switch（config）# config-revision 20
D. Switch（config）# vlan 50 name Tech
E. Switch（vlan）# vlan 50
F. Switch（vlan）# switchport trunk vlan 50
A.10.188.31.0/27
B.10.188.31.0/26
C.10.188.31.0/29
D.10.188.31.0/28
E.10.188.31.0/25
Refer to the exhibit.A network technician is asked to design a small network with redundancy. The exhibit represents this design， with all hosts configured in the same VLAN. What conclusions can be made about this design？（）
A.The design will function as intended
B.Spanning-tree will need to be used.
C.The router will not accept the addressing scheme.
D.The connection between switches should be a trunk.
E.The router interfaces must be encapsulated with the 802.1Q protocol.
A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2.
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
Refer to the exhibit.After a RIP route is marked invalid on Router_1， how much time will elapse before that route is removed from the routing table？（）
A.30 seconds
B.60 seconds
C.90 seconds
D.180 seconds
E.240 seconds
A.proxy
B.dual-stack
C.tunneling
D.dot1q
A.user EXEC mode
B.global configuration mode
C.privileged EXEC mode
D.auxiliary setup mode
A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Refer to the exhibit.S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology. While testing this configuration， a technician notes that pings are successfully from hosts on the 172.16.1.0/24 network to hosts on both the 172.16.2.0/25 and 172.16.0.2.128/25 networks. However， pings between hosts on the 172.16.2.0/25 and 172.16.2.128/25 network are not successful. What could explain this connectivity problem？（）
A.The ip subnet-zero command has been issued on the R1 router.
B.The RIPv2 dynamic routing protocol cannot be used across a Frame Relay network.
C.Split horizon is preventing R2 from learning about the R3 networks and R3 from learning about R2 networks.
D.The 172.16.2.0/25 and 172.16.2.128/25 networks are overlapping networks that can be seen by R1,but not between R2 and R3.
E.The 172.16.3.0/29 network used on the Frame Relay links is creating a discontiguous network between the R2 and R3 router subnetworks.
最新試題
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€邏輯地址范圍？（）
請參見圖示。從主機X 發出的到主機Y 的tracert 命令已成功。下列哪一項正確地反映了追蹤列表中顯示的中間網絡設備的順序？（）
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程？（）
請參見圖示。一臺路由器（其路由表如圖所示）收到發往192.168.1.4的數據包。路由器將如何處理該數據包？（）
請參見圖示。網絡中的主機A 正在向主機B 發送數據段。有關所交換的數據段的流量控制如圖所示。下列關于此通信的陳述，哪兩項是正確的？（）
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確？（）
請參見圖示。主機B 嘗試與主機C 建立TCP/IP 會話。在嘗試期間，San Francisco 器由器的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為10.10.1.2而目的IP 地址為10.31.1.20的數據包。捕獲該幀時，它的目的MAC 地址是什么？（）
請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置？（）
請參見圖示。下列哪組設備僅包含中間設備？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲写嬖诙嗌賯€廣播域？（）