The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）
A.The Gallant router has the wrong LMI type configured
B.Inverse ARP is providing the wrong PVC information to the Gallant router
C.The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
D.The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E.The IP address on the serial interface of the Attalla router is configured incorrectly
您可能感興趣的試卷
你可能感興趣的試題
A.Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the subinterface B
B.Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic
C.Configure many sub-interfaces on the same subnet
D.Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
A. buffering
B. cut-through
C. windowing
D. congestion avoidance
E. load balancing
A.A CSU/DSU terminates a digital local loop
B.A modem terminates a digital local loop
C.A CSU/DSU terminates an analog local loop
D.A modem terminates an analog local loop
E.A router is commonly considered a DTE device
F.A router is commonly considered a DCE device
A. 115.64.8.32
B. 115.64.7.64
C. 115.64.6.255
D. 115.64.3.255
E. 115.64.5.128
F. 115.64.12.128
A.can be used over analog circuits
B.maps Layer 2 to Layer 3 address
C.encapsulates several routed protocols
D.supports IP only
E.provides error correction
A.statically map IPV4 address to IPV6 addresses
B.configuration IPv4 tunnels between IPV6 islands
C.use DHCPv6 to map IPV4 addresses to IPV6 addresses
D.use proxying and translation to translate IPV6 packets into IPV4 packets
E.configure IPV6 directly
F.enable dual-stack routing
A.point-to-point
B.broadcast multi-access
C.nonbroadcast multi-access
D.nonbroadcast multipoint
E.broadcast point-to-multipoint
A.ermit all packets matching the first three octets of the source address to all destinations
B.permit all packet matching the last octet of the destination address and accept all source addresses
C.permit all packet matching the host bits in the source address to all destinations
D.permit all packet from the third subnet of the network address to all destinations
A. It supports VLSM.
B. It is used to route between autonomous systems.
C. It confines network instability to one area of the network.
D. It increases routing overhead on the network.
E. It allows extensive control of routing updates.
F. It is simpler to configure than RIP v2.
A.VTP
B.802.1Q
C.RSTP
D.STP
最新試題
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么？（）
請參見圖示。網絡中的主機A 正在向主機B 發送數據段。有關所交換的數據段的流量控制如圖所示。下列關于此通信的陳述，哪兩項是正確的？（）
下列哪些是私有IP 地址的地址范圍？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲写嬖诙嗌賯€(gè)廣播域？（）
PC 無法連接到任何遠程網站，無法ping 通其默認網關，也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常？（）
請參見圖示。公司路由器由于故障被更換。更換路由器之后，Education 辦公室內的主機C 和D 能夠相互ping 通，但是無法訪問Accounts 辦公室內的主機。此問題的原因可能是什么？（）
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是，從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題？（）
OSI 哪一層可提供有序的數據重構服務？（）
OSI 模型的哪兩項功能在第2層實現？（）
請參見圖示。主機A 和B 無法互相通信。此問題的原因是什么？（）