A.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1
B.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1
C.switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1
D.switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.The user at Workstation B reports that Server A cannot be reached.What is
preventing Workstation B from reaching Server A?()
A.The IP address for Server A is a broadcast address.
B.The IP address for Workstation B is a subnet address.
C.The gateway for Workstation B is not on the same subnet.
D.The gateway for Server A is not on the same subnet.
A.The switchport belongs only to VLAN 2
B.Interface fa0/0 will be in both VLAN 1 (by default) and VLAN 2
C.The exhibit shows interface fa0/0 to be dynamically mapped to VLAN 2
D.A network host can be connected to this interface
What is the under lying cause of this problem?()
A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.
A.switch to switch
B.switch to hub
C.switch to router
D.hub to hub
E.router to PC
A.The transport layer divides a data stream into segments and may add reliability and flow control information.
B.The data link layer adds physical source and destination addresses and an FCS to the segment.
C.Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information.
D.Packets are created when the network layer adds Layer 3 addresses and control information to a segment.
E.The presentation layer translates bits into voltages for transmission across the physical link.
A.802.1Q native VLAN frames are untagged by default.
B.802.1Q trunking ports can also be secure ports.
C.802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D.802.1Q trunks require full-duplex, point-to-point connectivity.
E.802.1Q trunks should have native VLANs that are the same at both ends.
A.it is a layer 2 messaging protocol which maintains vlan configurations across network.
B.it includes an 8-bit field which specifies the priority of a frame.
C.it is used exclusively for tagging vlan frames and dose not address network reconvergence following switched network topology changes.
D.it modifies the 802.3 frame header,and thus requires that the FCS be recomputed.
E.it is a trunking protocol capable of carring untagged frames.
A.255.255.255.0
B.255.255.255.192
C.255.255.255.250
D.255.255.255.252
A.RSTP cannot operate with PVST+.
B.RSTP defines new port roles.
C.RSTP defines no new port states.
D.RSTP is a proprietary implementation of IEEE 802.1D STP.
E.RSTP is compatible with the original IEEE 802.1D STP.
A.redundant
B.spanned
C.provisioned
D.converged
最新試題
以下哪兩種介質可提供高達1Gb/s 的帶寬?()
何時必須使用clock rate 命令配置路由器串行接口?()
請參見圖示。在網絡中,PC1向PC2發送了一條消息。PC2收到的幀如圖所示。該幀中的哪一信息確定了正確的目的應用程序?()
請參見圖示。下列哪組設備僅包含中間設備?()
在配置路由器時,網絡技術人員想要命名路由器。輸入hostname 命令后,技術人員會看到下列哪一項提示?()
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口?()
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程?()
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€(gè)邏輯地址范圍?()
傳輸層如何讓主機能同時針對不同應用程序維護多個通信流?()
請參見圖示。一臺主機正使用NAT 連接到Internet。下列哪三項IP 地址可實現此連接?()