A.802.1Q native VLAN frames are untagged by default.
B.802.1Q trunking ports can also be secure ports.
C.802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D.802.1Q trunks require full-duplex, point-to-point connectivity.
E.802.1Q trunks should have native VLANs that are the same at both ends.
您可能感興趣的試卷
你可能感興趣的試題
A.it is a layer 2 messaging protocol which maintains vlan configurations across network.
B.it includes an 8-bit field which specifies the priority of a frame.
C.it is used exclusively for tagging vlan frames and dose not address network reconvergence following switched network topology changes.
D.it modifies the 802.3 frame header,and thus requires that the FCS be recomputed.
E.it is a trunking protocol capable of carring untagged frames.
A.255.255.255.0
B.255.255.255.192
C.255.255.255.250
D.255.255.255.252
A.RSTP cannot operate with PVST+.
B.RSTP defines new port roles.
C.RSTP defines no new port states.
D.RSTP is a proprietary implementation of IEEE 802.1D STP.
E.RSTP is compatible with the original IEEE 802.1D STP.
A.redundant
B.spanned
C.provisioned
D.converged
A.Executing password recovery is required.
B.The virtual terminal lines are misconfigured.
C.Use Telnet to connect to RouterA and then to NewSwitch to correct the error.
D.Power cycle of NewSwitch will return it to a default configuration.
A.PPP
B.FDDI
C.Frame Relay PVC
D.NBMA
E.Frame Relay SVC
A.On router R2, configure a default static route to the 192.168.1.0 network.
B.On router R2, configure DNS to resolve the URL assigned to Web Server 2 to the 192.168.1.10 address.
C.On router R1, configure NAT to translate an address on the 209.165.100.0/24 network to 192.168.1.10.
D.On router R1, configure DHCP to assign a registered IP address on the 209.165.100.0/24 network to Web Server 2.
A.SSID
B.RTS/CTS
C.AES-CCMP
D.TKIP/MIC
E.RF channel
F.authentication method
A.NCP
B.LCP
C.ISDN
D.DLCI
E.SLIP
A.There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B.A single interface may be assigned multiple IPv6 addresses of any type.
C.Every IPv6 interface contains at least one loopback address.
D.The first 64 bits represent the dynamically created interface ID.
E.Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
最新試題
請參見圖示。主機A 和B 無法互相通信。此問題的原因是什么?()
請參見圖示。對于從主機A 向Web 服務器發出的網頁請求,正確的目的套接字?jǐn)?shù)字是什么?()
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么?()
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€邏輯地址范圍?()
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程?()
請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置?()
請參見圖示。在網絡中,PC1向PC2發送了一條消息。PC2收到的幀如圖所示。該幀中的哪一信息確定了正確的目的應用程序?()
下列哪些是私有IP 地址的地址范圍?()
請參見圖示。主機A 嘗試與主機C 建立TCP/IP 會話。在嘗試期間,路由器Y 的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為172.16.1.5而目的IP 地址為172.16.7.24的數據包。捕獲該幀時,它的源MAC 地址是什么?()
請參見圖示。哪種邏輯拓?fù)涫菍D示網絡的準確描述?()