A.The switch will ignore VTP summary advertisements.
B.The switch will forward VTP summary advertisements.
C.The switch will process VTP summary advertisements.
D.The switch will originate VTP summary advertisements.
E.The switch will create, modify and delete VLANs for the entire VTP domain.
您可能感興趣的試卷
你可能感興趣的試題
A.A remote physical layer problem exists.
B.The host NIC is not functioning.
C.TCP/IP has not been correctly installed on the host.
D.A local physical layer problem exists.
A.10.188.31.0/27
B.10.188.31.0/26
C.10.188.31.0/29
D.10.188.31.0/28
E.10.188.31.0/25
A.24
B.4
C.3
D.16
A.VTP allows routing between VLANs.
B.VTP allows a single switch port to carry information to more than one VLAN.
C.VTP allows physically redundant links while preventing switching loops.
D.VTP simplifies switch administration by allowing switches to automatically share VLAN configuration information.
E.VTP helps to limit configuration errors by keeping VLAN naming consistent across the VTP domain.
F.VTP enhances security by preventing unauthorized hosts from connecting to the VTP domain.
A.Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B.Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C.Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
D.Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.
A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and applyit to the terminal interfaces using theaccess-class command.
E.Create an access list and applyit to the terminal interfaces using theaccess-group command.
A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
A.Telnet to WANRouter and execute the command show interfaces S0/0
B.Telnet to WANRouter and execute the command show processes S0/0
C.Telnet to WANRouter and execute the command show running-configuration
D.Telnet to WANRouter and execute the command show controller S0/0
E.Physically examine the cable between WANRouter S0/0 and the DCE
F.Establish a console session on WANRouter and execute the command show interfaces S0/0
Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? （）
A.Switch A - Fa0/0
B.Switch A - Fa0/1
C.Switch B - Fa0/0
D.Switch B - Fa0/1
E.Switch C - Fa0/0
F.Switch C - Fa0/1
最新試題
請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置？（）
在路由器上使用Router#copy running-config startup-config 命令會產生什么效果？（）
請參見圖示。下列哪組設備僅包含中間設備？（）
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程？（）
請參見圖示。主機A 嘗試與主機C 建立TCP/IP 會話。在嘗試期間，路由器Y 的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為172.16.1.5而目的IP 地址為172.16.7.24的數據包。捕獲該幀時，它的源MAC 地址是什么？（）
在配置路由器時，網絡技術人員想要命名路由器。輸入hostname 命令后，技術人員會看到下列哪一項提示？（）
要將數據包發送到遠程網絡，應使用哪種設備？（）
下列哪些是私有IP 地址的地址范圍？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓撲中存在多少個廣播域？（）
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2？（）