A.VTP allows routing between VLANs.
B.VTP allows a single switch port to carry information to more than one VLAN.
C.VTP allows physically redundant links while preventing switching loops.
D.VTP simplifies switch administration by allowing switches to automatically share VLAN configuration information.
E.VTP helps to limit configuration errors by keeping VLAN naming consistent across the VTP domain.
F.VTP enhances security by preventing unauthorized hosts from connecting to the VTP domain.
您可能感興趣的試卷
你可能感興趣的試題
A.Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
B.Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
C.Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
D.Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.
A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and applyit to the terminal interfaces using theaccess-class command.
E.Create an access list and applyit to the terminal interfaces using theaccess-group command.
A.Configure the switch to be in VTP client mode.
B.Configure the switch to be in VTP domaint mode.
C.Configure the switch to be in VTP transparent mode.
D.Configure the switch to be in VTPv2
A.show interfaces interface
B.show interfaces interface trunk
C.show interfaces interface switchport
D.show ip interface brief
E.show interfaces vlan
A.Telnet to WANRouter and execute the command show interfaces S0/0
B.Telnet to WANRouter and execute the command show processes S0/0
C.Telnet to WANRouter and execute the command show running-configuration
D.Telnet to WANRouter and execute the command show controller S0/0
E.Physically examine the cable between WANRouter S0/0 and the DCE
F.Establish a console session on WANRouter and execute the command show interfaces S0/0
Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? ()
A.Switch A - Fa0/0
B.Switch A - Fa0/1
C.Switch B - Fa0/0
D.Switch B - Fa0/1
E.Switch C - Fa0/0
F.Switch C - Fa0/1
A.to make VTP easier to implement
B.to isolate broadcast traffic
C.to increase the size of the collision domain
D.to allow more devices to connect to the network
E.to logically group hosts according to function
F.to increase network security
A.proxy
B.dual-stack
C.tunneling
D.dot1q
A.one
B.two
C.three
D.four
E.six
F.fourteen
The Frame Relay network in the diagram is not functioning properly.What is the cause of the problem?()
A.The Gallant router has the wrong LM Itype configured
B.Inverse ARP is providing the wrong PVC information to the Gallant router
C.The S3 interface ofthe Steele router has been configured with the frame-relay encapsulation ietf command
D.The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
E.The IP address on the serial interface of the Attalla router is configured incorrectly
最新試題
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確?()
請參見圖示。主機A 和B 無法互相通信。此問題的原因是什么?()
請參見圖示。網絡中的所有設備均使用默認配置。此拓撲中需要多少個邏輯地址范圍?()
在路由器上使用Router#copy running-config startup-config 命令會產生什么效果?()
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口?()
傳輸層如何讓主機能同時針對不同應用程序維護多個通信流?()
請參見圖示。網絡中的所有設備均使用默認配置。此拓撲中存在多少個廣播域?()
請參見圖示。下列哪組設備僅包含中間設備?()
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是,從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題?()
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程?()