You are using ADU and are authenticated and associated to an access point. However， you are unable toobtain an IP address.
Which of these has caused this problem？（）
A.invalid SSID
B.invalid 802.1X authentication type
C.invalid encryption type
D.invalid WEP key
您可能感興趣的試卷
你可能感興趣的試題
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment.However， employees there have been experiencing problems when tracking objects using active RFIDtags. You use an access point scan to determine if the Location Appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct the problem？（）
A.allow for the automatic containment of rogue access points
B.ensure each area is covered by a minimum of three access points
C.ensure channels are deployed such that they do not overlap
D.ensure a minimum RSSI value of -50
On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the other LEDsare off.
What is this access point indicating？（）
A.It has lost contact with the controller.
B.It requires a code upgrade.
C.It is operating normally.
D.Its IP address already exists.
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing， butassociation using EAP-PEAP is functioning.
What needs to be enabled on the standalone access point tocorrect this issue？（）
A.a shared key
B.network EAP
C.open authentication plus EAP
D.open authentication plus MAC
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2. H-REAP AP2 has six other clients associated to it， which continue to pass traffic.
What has caused this problem？（）
A.H-REAP AP1 lost its connection to the controller.
B.H-REAP AP2 lost its connection to the controller.
C.H-REAP AP1 has reached its client limit.
D.H-REAP AP2 has reached its client limit.
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point has not been initialized with the primary controller
B.switch port is not enabled
C.switch does not support 802.3af
D.access point does not support 802.11h
E.incorrect switch power supply
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installation mode.When you set the link back to operational mode you loose association to the root bridge.
Which action willcorrect the problem？（）
A.Configure the proper channel.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
On a Cisco Aironet 1130AG Series standalone access point，the status LED is dark blue andblinking.
What does this indicate？（）
A.The access point is booting.
B.The internal radio has failed.
C.An access point buffer overflow is occurring.
D.A firmware upgrade is in progress.
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment. However，employees there have been experiencing problems when tracking objects using active RFIDtags. The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeout value.
Where and how should the RFID value be changed？（）
A.on the Cisco WCS， to 95 seconds
B.on the Cisco WCS， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the wireless controller， to 45 seconds
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment. However，employees there have been experiencing problems when tracking objects using active RFIDtags. The RFID tag data is not being collected.
On which device would you verify that RFIDs have beenenabled？（）
A.Cisco WCS
B.access point
C.location manager
D.wireless controller
You are trying to change the polling parameters used by the location manager via the Cisco WCS， and yourrequest is being denied.
What is wrong？（）
A.Your login does not have the correct permissions.
B.You must wait for the location server to become available.
C.Polling values can be changed only on the location server.
D.Polling values can be changed only in the maintenance window.
最新試題
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
A Cisco Wireless Location Appliance has been added to track RFID tags placed on laptops beingused in a school.Classrooms at the school have concrete block walls. During testing，you discoverthat the accuracy of the system needs to be improved.You decide to edit the map in the Cisco WCS to add the interior walls.How many interior walls can you add to improve the accuracy of thelocation appliance？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）