You are using ADU and are authenticated and associated to an access point. However，you areunable to obtain an IP address.
Which of these has caused this problem？（）
A.invalid SSID
B.invalid WEP key
C.invalid encryption type
D.invalid 802.1X authentication type
您可能感興趣的試卷
你可能感興趣的試題
A.network connections
B.location views
C.access points
D.object definitions
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners andCisco 7920 wireless IP phones.
In which mode should you deploy the additional access points toachieve the density required without excessive co-channel interference？（）
A.tracking mode
B.monitor mode
C.location mode
D.sniffer mode
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24PWR
Switch. However， when it is powered up， the access point fails.
What has caused this problem？（）
A.access point does not support 802.11h
B.incorrect switch power supply
C.switch port is not enabled
D.switch does not support 802.3af
E.access point has not been initialized with the primary controller
A.Acceptance Test Plan
B.Change Management
C.Incident Management
D.Configuration Management
A.Ongoing Support Handoff Meeting
B.Staff Training
C.Detailed Design Development
D.Staging and System Migration
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） isfailing， but association using EAP-PEAP is functioning.
What needs to be enabled on the standalone accesspoint to correct this issue？（）
A.network EAP
B.open authentication plus MAC
C.open authentication plus EAP
D.a shared key
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode.When you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the proper channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on astandalone WLAN.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.Publicly Secure Packet forwarding is enabled.
C.The access point is set to the least congested channel.
D.An address resolution protocol has been disabled.
On a Cisco Aironet 1130AG Series standalone access point， the status LED is dark blue andblinking.
What does this indicate？（）
A.The internal radio has failed.
B.A firmware upgrade is in progress.
C.An access point buffer overflow is occurring.
D.The access point is booting.
最新試題
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）