A.IPX
B.IP
C.UDP
D.TCP
您可能感興趣的試卷
你可能感興趣的試題
A.14
B.15
C.17
D.16
A.Location Appliance
B.controller-based access points
C.wireless clients
D.Wireless Control System
E.wireless controllers
A.4 to 6 times the tag beaconing rate
B.10 to 12 times the tab beaconing rate
C.8 to 10 times the tag beaconing rate
D.6 to 8 times the tag beaconing rate
A.Mirror
B.Rogue Detector
C.Sniffer
D.Monitor
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAPAP2.
H-REAP AP2 has six other clients associated to it,which continue to pass traffic.
What hascaused thisproblem?()
A.H-REAP AP1 has reached its client limit.
B.H-REAP AP2 has reached its client limit.
C.H-REAP AP2 lost its connection to the controller.
D.H-REAP AP1 lost its connection to the controller.
You are trying to change the polling parameters used by the location manager via the Cisco WCS,andyour request is being denied.
What is wrong?()
A.Polling values can be changed only in the maintenance window.
B.Polling values can be changed only on the location server.
C.Your login does not have the correct permissions.
D.You must wait for the location server to become available.
A.System Monitoring
B.Security Administration
C.Operations Setup
D.Problem Management
On a Cisco 1000 Series controller-based access point, the alarm LED is flashing red, but the otherLEDs are off.
What is this access point indicating?()
A.Its IP address already exists.
B.It is operating normally.
C.It requires a code upgrade.
D.It has lost contact with the controller.
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network,but clients using PEAP are failing to log on.
Which situation would result in thistype ofproblem?()
A.Posture validation has not been enabled.
B.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication.
C.Clients and server are not using certificates.
D.Clients have been set to validate the server identity.
You are configuring a wireless LAN controller for QoS.
Which 802.11e user priority tag should you apply to voice applications?()
A.3
B.6
C.4
D.1
最新試題
You have a very few Cisco 7920 wireless IP phones on your network, but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
You review the Failed Attempts logs on an AAA server and find: "unknown network access servererror." Which failure could produce this error?()
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side,which of the following actionsshould you perform on the wired infrastructure?()
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton, you should verify that the file name is which of the following?()
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications?()