A.device type and subnet
B.mac address and device type
C.serial number and version number
D.serial number and subnet
您可能感興趣的試卷
你可能感興趣的試題
A.lost connection to the controller
B.duplicate ip address
C.startup
D.site survey mode
A.enable self-healing.
B.configure location manager.
C.conduct client walkabout.
D.conduct radio scan.
A.disable auto rf and configure manually.
B.disable all 802.11b data rates.
C.power access point to full power.
D.hard code the channel.
A.infrastructure devices to associate only to this ssid
B.enable ip redirection on this ssid
C.set data beacon rate
D.multiple basic service set identification (bssid)
E.set infrastructure ssid
A.eap-peap
B.eap-fast
C.eap-cisco wireless (leap)
D.eap-tls
E.eap-md5
A.15
B.10
C.1
D.5
You are conducting a cdp-based discovery using an edge switch for the seed. there is a router between the switch and the wlse. none of the access points are discovered, and the discovery log shows the switch is snmp unreachable.
What is the problem?()
A.the snmp communities on the switch do not match the wlse.
B.the snmp communities on the access points do not match the wlse.
C.the snmp communities on the access points do not match the switch.
D.the snmp communities on the router do not match the wlse.
A.voip
B.rfid tags
C.data collection
D.802.11b and g clients
The ios of a north american cisco aironet 1230 series access point has become corrupt,
necessitating the need for a tftp firmware reload.
Before you press and hold the mode button,what must the file be named in order for the reload to occur?()
A.c1200-k9w7-tar.default
B.c1200-k9w7-tar.boot
C.c1200-k9w7-tar.123-7.ja1.tar
D.c1200-k9w7-tar.recover
lightweight access point has been connected to a catalyst 3550 24-pwr switch, and on power-up the access point fails.
What is the problem with the switch?()
A.the power supply has inadequate wattage.
B.power is incorrectly configured on the port.
C.it does not support 802.3af poe.
D.power is not enabled on the port.
最新試題
An REAP was supporting 16 WLANs, but now it only supports one.What happened to cause the change?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port?()
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference?()
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()