When configuring a cisco 3845 integrated services router to support 802.11b and g clients.
Which of the following commands would be correct?()
A.router(config-if)# speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
B.router(config-if)# speed 1.0 2.0 5.5 6.0 9.0 basic-11.0 12.0 basic-18.0 24.0 36.0 48.0 54.0
C.router(config-if)# speed basic-1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
D.router(config-if)# speed 1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
您可能感興趣的試卷
你可能感興趣的試題
A.enable concatenation on the non-root bridge only
B.enable concatenation on the root bridge only
C.enable concatenation on both the root bridge and non-root bridge
D.enable concatenation on the root bridge and set it as desirable on the non-root bridge
E.set concatenation as desirable on the root bridge and enable it on the non-root bridge
Eap-fast provides a secure tunnel during phase one to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel?()
A.x.509 certificate
B.generic token card
C.pre shared key
D.protected access credential
Your customer has deployed a cisco wireless location appliance within its warehouse
environment. however,employees there have been experiencing problems when tracking objects using active rfid tags. the rfid beacon rate is 10 seconds and you have discovered an issue with the rfid timeout value.
Where and how should the rfid value be changed?()
A.on the cisco wcs, to 95 seconds
B.on the wireless controller, to 45 seconds
C.on the wireless controller, to 95 seconds
D.on the cisco wcs, to 45 seconds
You are installing a cisco aironet 1000 series controller-based access point. when you boot it, all the leds on the access point blink together.
What does this indicate about the access point?()
A.duplicate ip address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
A.ipx
B.ip
C.udp
D.tcp
A.14
B.15
C.17
D.16
A.location appliance
B.controller-based access points
C.wireless clients
D.wireless control system
E.wireless controllers
A.48
B.36
C.12
D.24
A.10
B.5
C.15
D.20
A.project planning
B.configuration management
C.wireless readiness assessment
D.systems acceptance testing
E.site readiness specification
最新試題
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use?()
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it, allthe LEDs on the access point blink together.What does this indicate about the access point?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference?()
If it is properly deployed, a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller?()
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance?()
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast?()
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()