A.technology assessment
B.operations assessment
C.security assessment
D.security administration
E.change management
您可能感興趣的試卷
你可能感興趣的試題
A.15
B.10
C.1
D.5
A mobility group is created by a cisco wlcm and 4402 series wireless lan controller. A client that is anchored on the cisco wlcm roams to an access point on the 4402 controller. you then run a debug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’s perspective？（）
A.received mobile anchor export message
B.transmit plumbing duplex mobility tunnel message
C.received plumbing duplex mobility tunnel message
D.transmit mobile anchor export message
You are charged with implementing a secure wireless installation which will provide internet
access to client devices but will not allow communications between wireless clients.
In addition to implementing pspf or peer-to-peer blocking on the wireless side，which of the following actions should you perform on the wired infrastructure？（）
A.implement a cisco secure ips sensor.
B.implement 802.1x on the switch ports.
C.take no action， you have achieved your goal.
D.implement a protected port on the access switches.
You want to dynamically assign users to an 802.1q vlan as a result of their authentication.
In order to accomplish this，which two ietf radius attributes should you configure on the cisco secure acs？（）
A.083 tunnel-preference
B.066 tunnel-client-endpoint
C.064 tunnel-type
D.082 tunnel-assignment-id
E.081 tunnel-private-group-id
F.067 tunnel-server-endpoint
On a cisco aironet 1240ag series standalone access point， the radio led is dark blue and blinking， but the status led and ethernet led are both off.
what does this indicate？（）
A.a firmware upgrade is in progress.
B.an access point buffer overflow is occurring.
C.the access point is booting.
D.the internal radio has faile.
A.change management
B.configuration management
C.incident management
D.acceptance test plan
最新試題
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）