Look at the following exhibit. Which of the following correctly states the routes to be redistributed into OSPF? （）
A. The network 10.0.10.0/24 will be allowed and assigned a metric of 200
B. All networks except 10.0.0.0/8 will be allowed and assigned a metric of 200
C. The network 172.16.0.0/16 will be allowed and assigned a metric of 200
D. The network 192.168.1.0 will be allowed and assigned a metric of 100
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. R1 and R2 have been configured to share routing information via EIGRP. What will be the result of the configuration section shown for R2? （）
A. Any routes learned by R2 from the interface tied to the 172.16.0.0 network will not be advertised to neighbors on the 192.168.2.0 network.
B. Only routes learned by R2 from the interface tied to the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
C. Only the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network.
D. All networks, except the 172.16.0.0 network will be advertised to neighbors on the 192.168.2.0 network .
The following exhibit shows ipv6 route output. What would the metric be fo r a summary route that summarizes all three OSPFv3 routes displayed?（）
A. 160
B. 140
C. 120
D. 100
A. Only the path that is the feasible successor should be used.
B. Load balancing is disabled on t his router.
C. The router only performs equal - cost load balancing on all paths that have a metric greater than 1
D. The router performs equal - cost load balancing.
Refer to the exhibit. On the basis of the partial configuration, which two statements are correct? （）
A. Only routes 10.0.1.0/24 will be sent out all interfaces.
B. Only routes matching 10.0.0.0/8 will be advertised out interfaces other than Ethernet 0.
C. Only routes matching 10.0.0.0/8 will be advertised out Ethernet 0.
D. Only routes matching 10.0.1.0/24 will be advertised out Ethernet 0.
E. Only routes 10.0.1.0/24 will be allowed in the routing table.
F. All rout es will be advertised out interfaces other than Ethernet 0.
A. many - to - one
B. one - to - one
C. one - to - many
D. many - to - many
A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface
B. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interface
C. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface
D. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interface
E. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface
F. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?（）
A. Issue the command bandwidth 224 on the physical interface.
B. Issue the command bandwidth 56 on the physical interface.
C. Issue the command bandwidth 224 on each subinterface.
D. Issue the command bandwidth 56 on each subinterface.
Which statement is correct based upon the following output from the show command on RT1 ? （）
A. OSPFv3 establishes neighbor adjacencies by using global IPv6 addresses.
B. OSPFv3 establishes neighbor adjacencies by using Link - local addresses.
C. RT1 owns a subnet mask of 64 bits.
D. OSPFv3 establishes neighbor adjacencies by using IPv4 addr esses.
The following exhibit show s ipv6 route output. What would the metric be for a summary route that summarizes all three OSPFv3 routes displayed?（）
A. 160
B. 140
C. 120
D. 100
A. A generic Hello
B. Point - to - point Level 1, point - to -point Level 2, LAN Level 1, LAN Level 2
C. Point - to - point Level 1, point - to - point Level 2, LAN
D. Point - to - point, LAN Level 1, LAN Level 2
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0