A. Level 2 - 3
B. Level 1 - 2
C. Level 2
D. Level 0
E. Level 3
F. Level 1
您可能感興趣的試卷
你可能感興趣的試題
A. incorrect distribute lists have been configured
B. missing ip classless command
C. CEF not enabled
D. no default metric configured for EIGRP
If a metric is not specified for routes that are redistributed into OSPF, the defaul t metric that is assigned to the routes is 20, except for redistributed BGP routes.
What is the metric that is assigned to redistributed BGP routes?()
A. 200
B. 0
C. 1
D. 10
Refer to the exhibit. Which interoperability technique implemented on the dual - stack routers would allow connectivity between IPv6 sites across automatic created tunnels using the 2002::/16 prefix? ()
A. Dual Stack
B. NAT - PT
C. 6to4 tunnel
D. GRE tunnel
E. ISATAP tunnel
Refer to the exhibit. EIGRP has been configured on al l routers in the network. The command metric weights 0 0 1 0 0 has been added to the EIGRP process so that only the delay metric is used in the path calculations. Which router will R1 select as the successor and feasible successor for Network A?()
A. R 4 becomes the successor for Network A and will be placed in the routing table. R2 becomes the feasible successor for Network A
B. R4 becomes the successor for Network A and will be included in the routing table. No feasible successor will be selected a s the advertised distance from R2 is higher than the feasible distance
C. R2 becomes the successor and will be placed in the routing table. R4 becomes the feasible successor for Network A
D. R2 becomes the successor and will be placed in the routing t able. No feasible successor will be selected as the reported distance from R4 is lower than the feasible distance
A. 01 - 00 - 5e - 7f - 00 - 01
B. 01 - 01 - ef - ff - 00 - 01
C. 00 - 00 - 00 - 7f - 00 - 01
D. 10 - 00 - ef - ff - 00 - 01
Refer to the exhibit. Router RTA has been configured as a DHCP server. The two debug commands will generate output on RTA when Ho st A requests an IP address. Which set of DHCPD debug messages is in the correct sequence?()
A.DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to client
B.DH CPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: Sending DHCPACK to client
C.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to client
D.DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to client
E.DHCPD: Sending DHCPACK to client DHCPD: DHCPD ISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client
F.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client
A. Based on the default timers, OSPF d etects a failure faster than IS - IS does.
B. OSPF default timers permit more tuning than IS - IS does.
C. IS - IS is more efficient than OSPF in the use of CPU resources.
D. OSPF is more scalable than IS - IS because of its ability to identify normal, stub, an d NSSA areas.
E. IS - IS and OSPF are both Open Standard, link - state routing protocols which support VLSM.
Refer to the exhibit. A network administrator has configured DHCP services on the router asshown. DHCP clients connected to the FastEthernet0/0 interface are working properly. DHCP clients connected to the FastEthernet0/1 interface are not receiving addresses.
Which two statements contain recommendations that will solve the problem?()
A.The network shown in the output under the ip dhcp pool Central command should be changed to network 10.10.0.0 with a mask of 255.255.255.0
B.A second DHCP pool for network 10 .10.0.0/24 should be configured
C.An ip dhcp excluded - address global configuration command for network 10.10.0.0/24 should be issued
D.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/0 c onfiguration
E.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/1 configuration
Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:
*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active
*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.
Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.
Which statement best describes the reason for the error messages?()
A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.
B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.
C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
A router is running BGP and receives more than one route for a particular prefix. Assume all the routes for this prefix have the same attributes.
Which three path features would be reasons be for the rou ter to ignore some of the routes and not consider them as candidates for the best path?()
A. paths from an internal BGP (iBGP) neighbor if the local autonomous system (AS) appears in the AS_PATH
B. paths for which the NEXT_HOP is inaccess ible
C. paths from an external BGP (eBGP) neighbor if the local autonomous system (AS) appears in the AS_PATH
D. paths for which the NEXT_HOP is accessible
E. paths that are marked as synchronized in the show ip bgp output
F. paths that are marked as not synchronized in the show ip bgp output
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?()ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Which of the following features work the same in both RIP- 2 and RIPng?()
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?()
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?()
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?()D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Which of the following answers lists a multicast IPv6 address?()