On an Aironet card, LED 0 and LED 1 are blinking alternately.
What does this indicate? ()
A.The Aironet card is in power save mode.
B.The Aironet card is looking for a network association.
C.The Aironet card is joined to a network, but there is no network activity.
D.The Aironet card is joined to a network, and there is network activity.
您可能感興趣的試卷
你可能感興趣的試題
A.Static secure MAC addresses can be configured in conjunction with voice VLANs.
B.PortFast is automatically enabled when voice VLANs are configured.
C.PortFast must be manually configured when voice VLANs are configured.
D.Voice VLANs are typically configured on uplink ports.
E.Voice VLANs are typically configured on access ports.
Refer to the exhibit.
Which statement is true about the display of the command show pagp 1 neighbor command?()
A.STP packets are sent out the Gi0/1 interface only.
B.STP packets are sent out both the Gi0/1 and Gi0/2 interfaces.
C.CDP packets are sent out the Gi0/1 interface only.
D.CDP packets are sent out the Gi0/2 interface only.
A.allows an UDLD port to automatically reset when it has been shutdown
B.resets all UDLD enabled ports that have been shutdown
C.removes all UDLD configurations from interfaces that were globally enabled
D.removes all UDLD configurations from interfaces that were enabled per-port
Refer to the exhibit. When a profile is configured in the Aironet Desktop Utility,
which security option permits the configuration of host-based Extensible Authentication Protocol (EAP)?()
A.WPA/WPA2/CCKM
B.WPA/WPA2 Passphrase
C.802.1x
D.Pre-Shared Key (Static WEP)
Network topology exhibit:
Interface VLAN 101 exhibit:
Interface VLAN 102 exhibit:
Interface VLAN 104 exhibit:
Interface VLAN 105 exhibit:
You work as a network technician at. You study the network topology and the other exhibits carefully. Consider the distribution switches 1 and 2. 1 is the primary device for Vlan 101, 102, 105. 2 is the primary device for Vlan 103 and 104
Note: Please refer to the #2 scenario.
During routine maintenance, it became necessary to shutdown G1/0/1 on1 and2.
All other interface were up. During this time,1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group.
What can be done to make the group function properly ?()
A.On 1, disable preempt
B.On 2, decrease the priority value to a value less than 150
C.On 1, increase the decrement value in the track command to a value greater than 6
D.On 1, disable track command.
Network topology exhibit:
Interface VLAN 101 exhibit:
Interface VLAN 102 exhibit:
Interface VLAN 104 exhibit:
Interface VLAN 105 exhibit:
You work as a network technician at. You study the network topology and the other exhibits carefully. Consider the distribution switches1 and 2. 1 is the primary device for Vlan 101, 102, 105. 2 is the primary device for Vlan 103 and 104
Note: Please refer to the #2 scenario.
2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group.
What can be done to make the group function properly ?()
A.On 1, disable preempt
B.On 1, decrease the priority value to a value less than 190 and greater than 150
C.On 2, increase the priority value to a value greater 241 and less than 249
D.On 2, increase the decrement value in the track command to a value greater than 10 and less than 50.
Switch 1 was configured as shown below:
Based on the output shown above,
which statement is true?()
A.IP traffic matching access list is forwarded through VLANs 5-10.
B.All VLAN traffic in VLANs 5-10 that match access list will be forwarded, and all else will be dropped.
C.IP traffic matching VLAN list 5-10 will be forwarded, and all other traffic will be dropped.
D.All VLAN traffic matching VLAN list 5-10 will be forwarded, and all traffic matching access list is dropped.
E.None of the other alternatives apply
The following was configured on a switch:
Switch(config) # spanning-tree portfast bpdufilter default
What is the effect of this configuration command?()
A.If BPDUs are received by a port configured for PortFast, they are ignored and none are sent.
B.The command will enable BPDU filtering on all ports regardless of whether they are configured for BPDU filtering at the interface level.
C.If BPDUs are received by a port configured for Portfast, the port will transition to forwarding state.
D.If BPDUs are received by a port configured for PortFast, then PortFast is disabled and the BPDUs are processed normally.
E.None of the other alternatives apply.
An SVI has been configured on a device.
Which two statements are true about a switched virtual interface (SVI)?()
A.An SVI is normally created for the default VLAN (VLAN1) to permit remote switch administration.
B.Multiple SVIs can be associated with a VLAN.
C.SVI is another name for a routed port.
D.An SVI is created by entering the no switchport command in interface configuration mode.
E.An SVI provides a default gateway for a VLAN.
The following output was displayed on a switch.
Study the exhibit carefully. The administrator is verifying that a CEF FIB entry exists to destination network 192.168.150.0. Given the output generated by the "show ip cef" and "show adjacency detail" commands,
which three statements are true? ()
A.The "valid cached adjacency" entry indicates that CEF will put all packets going to such an adjacency to the next best switching mode.
B.The number 003071506800 is the MAC address of the source IP address.
C.There is a valid CEF entry for the destination network 192.168.150.0.
D.The number 003071506800 is the MAC address of the 192.168.199.3 next hop IP address.
E.The counters (0 packets, 0 bytes) indicate a problem with the 192.168.199.3 next hop IP address.
F.There is an adjacency for the 192.168.199.3 next hop IP address.
最新試題
Refer to the exhibit. What does the command channel-group 1 mode desirable do? ()
Refer to the exhibit. Which statement is true about the output?()
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method?()
During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network, Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit, which two statements are true?()
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct, what will be true about Switch 15?()
If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1 ?()
What is the configured priority value of the Vlan105’s group on DS2 ?()
How are STP timers and state transitions affected when a topology change occurs in an STP environment?()
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()