A.no switchport trunk native vlan vlan-id
B.switchport nonegotiate
C.no switchport mode dynamic desirable
D.switchport mode access
您可能感興趣的試卷
你可能感興趣的試題
A.switchport dynamic auto switchport dynamic auto
B.switchport access vlan 10 switchport mode dynamic desireable
C.switchport mode trunk switchport nonegotiate
D.Leave both ports with the default trunk settings
A.By default, native VLAN packets going out this port will be tagged.
B.Without an encapsulation command, 802.1Q will be the default encapsulation if DTP fails to negotiate a trunking protocol.
C.The interface will support the reception of tagged and untagged traffic.
D.If the device connected to this port is not 802.1Q-enabled, it will not be able to handle 802.1Q packets.
A.PortFast, UplinkFast, and BackboneFast specific configurations are ignored in Rapid PVST mode.
B.RSTP is enabled globally and uses existing STP configuration.
C.Root and alternative ports transition immediately to the forwarding state.
D.Convergence is improved by using sub-second timers for the blocking, listening, learning, and forwarding port states.
A.Unidirectional link detection is achieved through monitoring STP BPDUs.
B.It is recommended that it be enabled globally rather than on an individual port.
C.When an error is detected, normal mode will disable a port.
D.It is recommended that it be enabled in normal mode.
E.It is recommended that it be used with the loop guard feature.
A.Upon startup, the port transmits 10 BPDUs. If the port receives a BPDU, PortFast and BPDU guard are disabled on that port and it assumes normal STP operation.
B.The access port ignores any received BPDU.
C.If the port receives a BPDU, it is placed into the error-disable state.
D.BPDU guard is only configured globally and the BPDU filter is required for port-level configuration.
A.STP will be disabled on the port.
B.PortFast can also be configured on trunk ports.
C.PortFast is required to enable port-based BPDU guard.
D.PortFast is used for both STP and RSTP host ports.
E.PortFast is used for STP-only host ports.
A.root
B.designated
C.alternate
D.backup
E.forwarding
F.learning
A.dynamic desirable (VTP domain A) to dynamic desirable (VTP domain A)
B.dynamic desirable (VTP domain A) to dynamic desirable (VTP domain B)
C.dynamic auto (VTP domain A) to dynamic auto (VTP domain A)
D.dynamic auto (VTP domain A) to dynamic auto (VTP domain B)
E.dynamic auto (VTP domain A) to nonegotiate (VTP domain A)
F.nonegotiate (VTP domain A) to nonegotiate (VTP domain B)
A.Transparent mode always has a configuration revision number of 0.
B.Transparent mode cannot modify a VLAN database.
C.Client mode cannot forward received VTP advertisements.
D.Client mode synchronizes its VLAN database from VTP advertisements.
E.Server mode can synchronize across VTP domains.
A.Layer 2 switching and Layer 3 routing are mutually supported.
B.The port will not be associated with any VLAN.
C.The routed switch port supports VLAN subinterfaces.
D.The routed switch port is used when a switch has only one port per VLAN or subnet.
E.The routed switch port ensures that STP remains in the forwarding state.
最新試題
Refer to the exhibit. Based on the output of the show spanning-tree command, which statement is true? ()
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network, Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit, which two statements are true?()
Which three statements about STP timers are true?()
Which two statements about the various implementations of STP are true?()
How are STP timers and state transitions affected when a topology change occurs in an STP environment?()
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this?()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()
Refer to the exhibit. What does the command channel-group 1 mode desirable do? ()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()