During testing of network redundancy in a fully meshed enterprise campus， a problem has been reported. Both distribution multilayer switches are fully configured for redundancy； clients operate normally when the primary multilayer distribution switch is operating. All clients drop connections outside of their respective access layer group when the primary distribution switch is shut down and the secondary distribution switch is still operational. Additional information indicates that the secondary distribution switch is able to ping major corporate and Internet locations.
Which item would be the best point of troubleshooting for this connectivity issue？ （）
A.client network configuration
B.VLAN mapping
C.inter-switch trunk configuration
D.UDLD configuration
E.first-hop redundancy protocol
您可能感興趣的試卷
你可能感興趣的試題
A.aaa port-auth enable
B.radius port-control enable
C.dot1x system-auth-control
D.switchport aaa-control enable
A.The port is configured for both data and voice traffic.
B.The port is fully dedicated to forwarding voice traffic.
C.The port will operate as an FXS telephony port.
D.Voice traffic will be redirected to VLAN 222.
A remote host can be pinged from all switches except one.
Which of the following is the most likely reason for this failure？（）
A.VTP pruning has isolated the switch.
B.IP routing is disabled on the switch.
C.PoE is failing on the remote port.
D.There is a loop in the topology.
A.The command enables both loop guard and root guard.
B.The command changes the status of loop guard from the default of disabled to enabled.
C.The command activates loop guard on point-to-multipoint links in the switched network.
D.The command will disable EtherChannel guard.
A.Packets are distributed across the ports in the channel based on both the source and destination MAC addresses.
B.Packets are distributed across the ports in the channel based on both the source and destination IP addresses.
C.Packets are balanced across the ports in the channel based first on the source MAC address， then on the destination MAC address， then on the IP address.
D.Packets are distributed across the access ports in the channel based first on the source IP address and then the destination IP addresses.
A.network management
B.improving QoS
C.determining budget
D.reducing costs
E.increasing competitiveness
F.improving customer support
You work as a network engineer for. You study the exhibit carefully. Based on the output of the show command，
what can you determine regarding EIGRP routing being performed by the switch？ （）
Exhibit：
A.There are 20 neighbors in the EIGRP neigbor table.
B.EIGRP is running normally and receiving IPv4 routing updates.
C.The switch has not established any neighbor relationships. Further network testing and troubleshooting must be performed to determine the cause of the problem.
D.EIGRP status cannot be determined. The command show ip eigrp topology would determine the routing protocol status.
You work as a network engineer for . You study the exhibit carefully. Based upon the output shown，
what can you determine？（）
Exhibit：
A.VLAN 30 is not operational due to the fact that there are no packet or byte counts indicated.
B.The IP Cisco Express Forwarding configuration is capable of supporting IPv6.
C.Cisco Express Forwarding load balancing has been disabled.
D.SVI VLAN 30 connects directly to the 10.1.30.0/24 network due to a valid glean adjacency.
You work as a network engineer for. You study the exhibit carefully. Based on the configuration
shown，
which two statements are correct regarding this Layer 3 security configuration example？ （）
Exhibit：
A.Source IP and MAC filtering on VLANs 10 and 11 will occur.
B.The switch will drop the configured MAC and IP address source bindings and forward all other traffic.
C.DHCP snooping will be automatically enabled on the access VLANs.
D.IP Source Guard is enabled.
E.Static IP source binding can only be configured on a routed port.
You work as a network engineer for. You study the exhibit carefully. From the configuration sample shown of a Cisco Catalyst 3560 Series Switch，
what can you determine regarding Layer 3 routing functionality of the interface？（）
Exhibit：
A.The interface is configured correctly for Layer 3 routing capabilities.
B.The interface needs an additional configuration entry to enable IP routing protocols.
C.The interface subcommand ip routing is required to enable IP routing on the interface.
D.An SVI interface is required to enable IP routing for network 192.20.135.0.
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. Which statement is true about the output？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Which two statements are true when the extended system ID feature is enabled？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）