A. It is used to validate the sources of VTP advertisements sent between switches.
B. It is used to access the VTP server to make changes to the VTP configuration.
C. It allows two VTP servers to exist in the same domain, each configured with different passwords.
D. It is the password required when promoting a switch from VTP client mode to VTP server mode.
E. It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.
您可能感興趣的試卷
你可能感興趣的試題
A company is experiencing network delays. The network administrator discovers that a worker in a location far from the MDF has connected an old 10BASE-T switch with redundant links to the existing network.
How could this action be responsible for the impaired network performance?()
A. Connecting a host to the old switch has created a broadcast storm.
B. The 10BASE-T switch forced the entire network to be reduced to 10 Mbps operation.
C. The old switch does not support VLANs, which has disabled the VLAN configuration of the entire the network.
D. The old switch does not support full-duplex operation, effectively forcing half-duplex operation throughout the network.
E. Spanning Tree Protocol has elected the old switch as the root bridge, creating inefficient data paths through the switched network.
A.DHCP
B.SMTP
C.SNMP
D.FTP
E.HTTP
F.TFTP
A. Denmark exchanges with Utah, Paris, and Berlin.
B. Utah exchanges only with Denmark.
C. Berlin exchanges with Denmark, Utah, and Paris.
D. Paris exchanges only with Denmark.
E. Denmark exchanges with only Paris and Utah.
A. Individual statements in a named access list may be deleted.
B. They require a numbered range from 1000 to 1099.
C. When created, they must be specified as standard or extended.
D. They are created with the ip access-list command.
E. The entire access list must be deleted before editing.
F. They are applied with the ip name-group command.
A. point-to-point
B. broadcast multi-access
C. nonbroadcast multi-access
D. nonbroadcast multipoint
E. broadcast point-to-multipoint
A. RIP v1
B. RIP v2
C. IGRP
D. OSPF
E. EIGRP
A. ping 127.0.0.0
B. ping 203.125.12.1
C. telnet 127.0.0.1
D. ping 127.0.0.1
E. tracert 203.125.12.1
A. in order to optimize the path that frames take from source to destination
B. to increase the priority so a designated port will become a root port
C. to increase the BID, so the switch is more likely to become root bridge
D. in order to allow VLANs to be sent from one switch to another across a single link
E. to force a given switch to become an STP server
A. designated ports.
B. duplex operating mode.
C. fast mode ports.
D. root bridge.
E. root ports.
F. BDPU priority.
A. 172.16.42.0
B. 172.16.107.0
C. 172.16.208.0
D. 172.16.252.0
E. 172.16.254.0
最新試題
Which of the following contribute to congestion on an Ethernet network?()
What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?()
Which characteristics are representative of a link-state routing protocol?()
How many usable sub network and usable hosts per subnet result in the network address 201.105.13.0 is sub netted with a mask of /26? ()
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? ()
Identify three valid host addresses in the 192.168.27.0 network with a subnet mask of 255.255.255.240. ()
Which of the following if addresses can be assigned to host devices?()
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? ()
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?()
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()