A. to make VTP easier to implement
B. to isolate broadcast traffic
C. to increase the size of the collision domain
D. to allow more devices to connect to the network
E. to logically group hosts according to function
F. to increase network security
您可能感興趣的試卷
你可能感興趣的試題
A. Install anti-virus software on the student computers.
B. Put the faculty computers in a separate VLAN.
C. Power down the switches that connect to faculty computers when they are not in use.
D. Remove the student computers from the network and put them on a peer-to-peer network.
E. Create an access list that blocks the students from the Internet where the hacking tolls are located.
A. VTP allows routing between VLANs.
B. VTP allows a single switch port to carry information to more than one VLAN.
C. VTP allows physically redundant links while preventing switching loops.
D. VTP simplifies switch administration by allowing switches to automatically share VLAN configuration information.
E. VTP helps to limit configuration errors by keeping VLAN naming consistent across the VTP domain.
F. VTP enhances security by preventing unauthorized hosts from connecting to the VTP domain.
A. TestKing1(config-if)# switchport port-security maximum 1
B. TestKing1(config)# mac-address-table secure
C. TestKing1(config)# access-list 10 permit ip host
D. TestKing1(config-if)# switchport port-security violation shutdown
E. TestKing1(config-if)# ip access-group 10
A.NCP
B.ISDN
C.SLIP
D.LCP
E.DLCI
A. ARP
B. CDP
C. DHCP
D. DNS
E. ICMP
A. to prevent routing loops
B. to create a default route
C. to provide multiple gateways for hosts
D. to maintain a loop-free Layer 2 network topology
E. to enhance the functions of SNMP
A. defines how the media is accessed
B. supplies a token to determine which host has access to the media
C. defines the encoding of electrical signals on the wire
D. determines the preamble bits
A. path cost
B. lowest port MAC address
C. VTP revision number
D. highest port priority number
E. port priority number and MAC address
A. It is used with the OSPF priority values to determine which OSPF router will become the DR or BOR in a point-to-point network
B. It is used with the OSPF priority values to determine which interface will be used to form a neighbor relationship with another OSPF router
C. It is used with the OSPF priority values to determine which router will become the DR or BOR in a multi access network
D. It is used to determine which interfaces will send Hello packets to neighboring OSPF routers
A. Show vlan
B. Show mac-address-table
C. Show vtp status
D. show spanning-tree root
E. show ip interface brief
最新試題
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
Which of the following host addresses are member of networks that can be routed across the public Internet? （）
How many usable sub network and usable hosts per subnet result in the network address 201.105.13.0 is sub netted with a mask of /26? （）
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）
Which of the following contribute to congestion on an Ethernet network?（）
Which of the following describe router functions?（）
Which statement describes the rule of split horizon?（）
Given a subnet mask of 255.255.255.224, which of the following addresses can be assigned to network hosts?（）
TestKing.com has allocated the IP add 199.144.27.0 is its network, to provide flexibility for the LAN design, a subnet mask of 255.255.255.240 has been chosen. Which of the following address can be assigned to LAN on the resulting subnets.（）
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）