Refer to the exhibit. On the basis of the configuration provided, how are the Hello packets sent by R2 handled by R5 in OSPF area 5?（）
A. The Hello packets will be exchanged and adjacency will be established between routers R2 and R5.
B. The Hello packets will be exchanged but the routers R2 and R5 will become neighbors only.
C. The Hello packets will be dropped and no adjacency will be established between routers R2 and R5.
D. The Hello packets will be dropped but the routers R 2 and R5 will become neighbors.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? （）
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
A. Verify that the EIGRP hello and hold timers match exactly.
B. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.
C. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.
D. Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.
Refer to the exhibit. Routing updates for the 192.168.1.0 network are being received from all three neighbors. Which statement is correct regarding the result of the con figuration shown? （）
A. The router will prefer the next hop of 172.16.1.1 for packets destined for the 192.168.1.0 network.
B. The router will prefer the next hop of 172.26.1.1 for packets destined for the 192.168.1.0 network.
C. The router will adve rtise the 192.168.1.0 network only to 172.30.1.1.
D. The router will advertise the 192.168.1.0 network only to 172.26.1.1.
E. The router will prefer the next hop of 172.26.1.1 for packets except those destined for the 192.168.1.0 network.
Refer to the e xhibit. It is desired to set up a BGP neighbor relationship between routers R1 and R4. BGP packets between them could travel through R2 or R3. What is the simplest configuration that will allow for failover?（）
A. Configure BGP n eighbor relationships between all interfaces on R1 and R4.
B. Install a direct connection between R1 and R4.
C. Configure loopback interfaces on R1 and R4 to provide the update source address for BGP packets.
D. Configure only one neighbor relationship between R1's 192.168.1.2 interface and R4's 172.16.10.2 interface.
A. In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas.
B. In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas.
C. In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas.
D. In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.
A. RTA will forward RP announcements provided they are within the scope of 31.
B. RTA will originate RP announcements with TTL s et to 31.
C. RTA will originate RP announcements for multicast groups that match access - list 5.
D. RTA will drop all RP announcements it receives if the TTL field is greater than 31.
A. Summarized routes are unacceptable
B. They will appe ar in the OSPF routing table as type E2 routes
C. Only routes with lower administrative distances will be imported
D. All imported routes are to be automatically summarized if possible
A. RIP
B. BGP
C. IS - IS
D. OSPF
E. EIGRP
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）
A. The redistribution command should be reentered with the match route - type parameter included.
B. The redistribution command should be reentered wit h the route - map map - tag parameter included.
C. The redistribution command should be reentered with the metric metric - value parameter included.
D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown?（）
A. Interface authentication must be configured
B. The routing processes must be configured with an area ID
C. IP unicast routing must be enabled
D. IPv4 ad dresses must be applied to the interfaces
最新試題
Which of the following are true of both OSPFv2 and OSPFv3?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）