Refer to the exhibit.
What is the configuration an example of? ()
A. GLBP weighting
B. default AVF and AVG configuration
C. GLBP MD5 authentication
D. GLBP text authentication
E. GLBP timer manipulation
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
Which Virtual Router Redundancy Protocol (VRRP) statement is true about the roles of the master virtual router and the backup virtual router?()
A. Router A is the master virtual router, and Router B is the backup virtual router. When Router A fails, Router B will become the master virtual router. When Router A recovers, Router B will maintain the role of master virtual router.
B. Router B is the master virtual router, and Router A is the backup virtual router. When Router B fails, Router A will become the master virtual router. When Router B recovers, it will regain the master virtual router role.
C. Router A is the master virtual router, and Router B is the backup virtual router. When Router A fails, Router B will become the master virtual router. When Router A recovers, it will regain the master virtual router role.
D. Router B is the master virtual router, and Router A is the backup virtual router. When Router B fails, Router A will become the master virtual router. When Router B recovers, Router A will maintain the role of master virtual router.
Exhibit:
Exhibit:
You work as a network engineer at Company. You study the exhibit carefully. Which GLBP device hosts receive the MAC address assignment?()
A. R1
B. R2
C. The AVG
D. The AVF
E. None of the other alternatives apply
On a 3550 EMI switch,
which three types of interfaces can be used to configure HSRP? ()
A. Loopback interface
B. SVI interfac
C. Routed port
D. Access port
E. EtherChannel port channel
F. BVI interface
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails? ()
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails.
What command would you use if you wanted to configure this? ()
A. en standby preempt
B. standby preempt enable
C. standby preempt
D. hot standby preempt
A. Define the encapsulation type.
B. Define the standby router.
C. Define the standby IP address.
D. Enable the standby priority.
Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4. When Link A fails, router R2 (Link B) becomes the active router.
Which router will assume the active role when Link A becomes operational again?" ()
A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the event of Link B failure.
D. The third member of the HSRP group, router R3, will take over the active role only in event of router R2 failure.
Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1 and R2, and hosts A and B have been configured as shown.
Which statement can be derived from the exhibit?()
A. The hostA default gateway has been configured as 10.88.1.10/24.
B. The GLBP weighted load balancing mode has been configured.
C. The GLBP round-robin, load-balancing mode has been configured.
D. The GLBP host-dependent, load-balancing mode has been configured.
E. The hostA default gateway has been configured as 10.88.1.1/24.
F. The hostA default gateway has been configured as 10.88.1.4/24.
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails?()
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
Routers can send hello messages in three HSRP states.
Which ones are they?()
A. Standby
B. Learn
C. Listen
D. Speak
E. Active
最新試題
How are STP timers and state transitions affected when a topology change occurs in an STP environment?()
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals?()
Refer to the exhibit. Which statement is true about the output?()
Which statement is correct about the use of the virtual interface on a WLC ?()
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1? ()
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this?()
What two things will occur when an edge port receives a BPDU?()
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain, the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change?()