HSRP has been configured between two Company devices.
Which of the following describe reasons for deploying HSRP？ （）
A. HSRP provides redundancy and fault tolerance
B. HSRP allows one router to automatically assume the function of the second router if the second router fails
C. HSRP allows one router to automatically assume the function of the second router if the second router starts
D. HSRP provides redundancy and load balancing
您可能感興趣的試卷
你可能感興趣的試題
You want to implement a high availability network using two Cisco routers. You also want to ensure that the stat of the WAN interfaces can be tracked in doing so.
Which router redundancy protocol cannot be configured for interface tracking？ （）
A. GLBP
B. HSRP
C. RPR
D. VRRP
E. SLB
F. RPR+
G. None of the other alternatives apply
You need to configure two Company routers for high availability.
Which protocol enables a group of routers to form a single virtual router and use the real IP address of a router as the gateway address？ （）
A. HSRP
B. IRDP
C. Proxy ARP
D. GLBP
E. VRRP
F. None of the other alternatives apply
You have just purchased a new Cisco 3560 switch running the enhanced IOS and need configure it to be installed in a high availability network. On a 3560 EMI switch，
which three types of interfaces can be used to configure HSRP？（）
A. SVI interface
B. Access port
C. EtherChannel port channel
D. Loopback interface
E. Routed port
F. BVI interface
A. QoS classified at layer 3 using IP precedence or DSCP.
B. Guaranteed rate service.
C. Implemented using FIFO queues.
D. All traffic has an equal chance of being dropped.
The Company is rolling out Cisco’s Architecture for Voice， Video and Integrated Data （AVVID）.
Which of the following choices represent the fundamental intelligent network services in Cisco’s AVVID？ （）
A. Quality of Service （QoS）
B. Intelligent platforms
C. Mobility and scalability
D. Security
E. High availability
Refer to the exhibit.
What is the effect when the switchport priority extend cos 3 command is configured on the switch port interface connected to the IP phone？（）
A. The IP phone is enabled to override with aCoS value of 3 the existing CoS marking of the PC attached to the IP phone.
B. The switch will no longer tag incoming voice packets and will extend the trust boundary to the distribution layer switch.
C. RTP will be used to negotiate aCoS value based upon bandwidth utilization on the link.
D. Effectively， the trust boundary has been moved to the PC attached to the IP phone.
E. The computer is now establishing theCoS value and has effectively become the trust boundary.
Refer to the exhibit.
Which Catalyst switch interface command would be used to cause the switch to instruct the phone to override the incoming CoS from the PC before forwarding the packet to the switch？（）
A. mls qos cos 2 override
B. switchport priority extend cos 11
C. switchport priority extend trust
D. switchport priority extend none
E. mls qos cos 2
F. switchport priority extend cos 2
You have configured voice VLANs on Catalyst switch R1.
Which two statements are true about the operation of voice VLANs on this device？ （）
A. When the voice VLAN feature is enabled， all untagged traffic is sent according to the default CoS priority of the port.
B. Enabling voice VLANs enables the switch to create multiple queues for traffic that is entering a port.
C. When voice VLANs are configured on a trunk link， UplinkFast must also be enabled.
D. Voice VLANs are configured to enable the switch to forward frames marked with the proper CoS values over separate physical links.
E. Enabling voice VLANs enables the switch to forward frames with a specific 802.1P marking.
Refer to the exhibit.
Which statement is true about the configuration that is shown？ （）
A. Untagged ingress traffic will be dropped.
B. Ingress traffic from the host will be tagged with theCoS value of 5.
C. Tagged and untagged ingress traffic will be carried on VLAN 1.
D. Untagged ingress traffic will be marked with the default CoS value of the port.
The Company network administrator has entered the "auto qos voip cisco-phone" command on switch R1.
What does this command do？（）
A.It disables the trust boundary feature because the switch knows a Cisco IP phone is attached.
B.The switch assigns a CoS value of 5 to incoming packets.
C.If a Cisco IP phone is attached and removed， the switch continues to trust the CoS values as long as the switch is not rebooted.
D.It turns on STP to see if a Cisco IP phone is attached.
E.If a Cisco IP phone is attached， the switch trusts the CoS.
F.None of the other alternatives apply.
最新試題
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
What two things will occur when an edge port receives a BPDU？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）