A. An automatic 6to4 tunnel does not req uire dual - stack (IPv4 and IPv6) routers at the tunnel endpoints.
B. An automatic 6to4 tunnel allows multiple IPv4 destinations.
C. A manually configured IPv6 in IPv4 tunnel allows multiple IPv4 destinations.
D. A manually configured IPv6 in IPv4 tunnel does not require dual- stack (IPv4 and IPv6) routers at the tunnel endpoints.
您可能感興趣的試卷
你可能感興趣的試題
A. IPv6 allows a host to create its own IPv6 address that will allow it to communicate to other devices on a network configured via DHCP. IPv4 does not provide a similar capability for hosts.
B. IPv6 provides for more host IP addresses but IPv4 provides for more network addresses.
C. Hosts can be configured to receive both IPv4 and IPv6 addresses via DHCP.
D. Host configuration options for IPv4 can be either statically assigned or assigned via DHCP.Host configuration options for IPv6 can be statically assigned only.
E. IPv4 and IPv6 addresses c an be simultaneously assigned to a host but not to a router interface.
Refer to the exhibit. IP multicast configuration changes have been made on several routers.However, the IP multicast table displayed in the exhibit still does not reflect the changes. What should be done to display the new routing table information? （）
A. Issue the clear ip route * privileged EXEC command.
B. Issue the clear ip igmp group privileged EXEC command.
C. Issue the no ip mroute - cache privileged EXEC command.
D. Issue the clear ip mroute privileged EXEC command.
A. The edge routers can use any locally configured IPv6 address.
B. Hosts and routers inside a 6to4 site will need a special code.
C. An edge router must use IPv6 address of 2002::/16 in its prefix.
D. IPv4 traffic is encapsulated with an IPv6 header.
A. 2031::130F::9C0:876A:130B
B. 2031:0000:130F:0000:0000:09C0:876A:130 B
C. 2031:0:130F:::9C0:876A:130B
D. 2031::130F:0::9C0:876A:130B
E. 2031:0:130F:0:0:09C0:876A:130B
F. 2031:0:130F::9C0:876A:130B
A. Unicast
B. Private
C. Broadca st
D. Public
E. Multicast
F. Anycast
A. ip routing ipv6
B. ipv6 unicast - routing
C. ipv6 routing
D. ip classless
E. ipv6 cef
A. Dual stack
B. NAT
C. Flow label
D. Mobile IP
E. 6to4 tunneling
F. Anycast
G. MBGP
A. router ospf ipv6 process - id
B. ipv6 ospf process - id
C. router ospf process - id
D. ipv6 router ospf process - id
A. Link LSA
B. Interarea prefix LSA for ABRs
C. Router LSA
D. Switch LSA
E. Intra - area prefix LSA
F. None of the above
A. a request made by a node to join a specified multicast group
B. a request made by a node for its IP address
C. a request made by a node for the IP address of the DHCP server
D. a request made by a node for the IP address of the local router
最新試題
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Which of the following answers lists a multicast IPv6 address?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Which of the following are true of both OSPFv2 and OSPFv3?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0