You are the network administrator at Company and switch R1 is configured as shown below： Interface gigethernet 0/1 Switchport mode trunk
Switchport trunk encapsulation dot1q Switchport trunk native vlan 5
If untagged frames are arriving on interface gigethernet 0/1 of R1，
which of the following statement are correct？（）
A. Untagged frames are automatically assumed to be in VLAN 5.
B. Untagged frames are defaulted to VLAN 1 traffic.
C. Untagged frames are dropped because all packets are tagged when dot1q trunked.
D. Untagged frames are determined on the other switch
E. Untagged frames are not supported on 802.1Q trunks.
您可能感興趣的試卷
你可能感興趣的試題
If you were to configure an ISL Ethernet trunk between two Cisco switches， named R1 and R2，
what would you have to include at the end of the link for the trunk to operate correctly？ （）
A. An identical VTP mode.
B. An identical speed/duplex.
C. An identical trunk negotiation parameter.
D. An identical trunk encapsulation parameter.
Which of the following technologies would an Internet Service Provider use to support overlapping customer VLAN ID’s over transparent LAN services？ （）
A. 802.1q tunneling
B. ATM
C. SDH
D. IP Over Optical Networking
E. ISL
You need to connect two Company core switches via an ISL trunk.
Which statement is true regarding the configuration of ISL trunks？ （）
A. A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.
B. All Catalyst switches support ISL trunking.
C. A Catalyst switch will report giants if one side is configured for ISL while the other side is not.
D. ISL trunking requires that native VLANs match.
E. None of the other alternatives apply
A new Company switch was just configured using the "switchport trunk native vlan 7" command.
What does this interface command accomplish？（）
A. Causes the interface to apply ISL framing for traffic on VLAN 7
B. Configures the trunking interface to forward traffic from VLAN 7
C. Configures the interface to be a trunking port and causes traffic on VLAN 7 to be 802.1q tagged
D. Configures the trunking interface to send traffic from VLAN 7 untagged
E. None of the other alternatives apply
You need to configure a new Company switch to support DTP.
Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames？ （）
A. Access
B. No negotiate
C. Trunk
D. Dynamic desirable
E. Dynamic auto
F. None of the other alternatives apply
While using a packet analyzer， you notice four additional bytes being added to the packets in the Company network.
Which protocol inserts a four byte tag into the Ethernet frame and recalculates CRC value？ （）
A. DTP
B. VTP
C. 802.1Q
D. ISL
E. None of the other alternatives apply
You need to configure a new Company switch for trunking.
Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）
A. CompanySwitch（config-if）#switchport trunk encapsulation dot1q
B. CompanySwitch（config-if）#switchport trunk encapsulation itef
C. CompanySwitch（config-if）#switchport trunk encapsulation fddi
D. CompanySwitch（config-if）#switchport trunk encapsulation isl
E. None of the other alternatives apply
Switch R1 has been configured with DTP using the desirable option.
Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）
A. The interface actively attempts to convert the link to a trunk link.
B. The interface is put into permanent trunking mode but prevented from generating DTP frames.
C. The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
D. The interface is put into a passive mode， waiting to convert the link to a trunk link.
E. None of the other alternatives apply
The core Company switches are configured to use 802.1Q trunks.
Which three statements are correct with regard to the IEEE 802.1Q standard？（）
A. The IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
B. The packet is encapsulated with a 26 byte header and a 4 byte FCS
C. The protocol uses point-to-multipoint connectivity
D. The protocol uses point-to-point connectivity
E. The IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
F. The IEEE 802.1Q frame retains the original MAC destination address
Refer to the exhibit. On the basis of the output generated by the show commands，
which two statements are true？（）
A. Because it is configured as a trunk interface， interface gigabitethernet 0/1 does not appear in the show vlan output.
B. VLAN 1 will not be encapsulated with an 802.1q header.
C. There are no native VLANs configured on the trunk.
D. VLAN 2 will not be encapsulated with an 802.1q header.
E. All interfaces on the switch have been configured as access ports.
F. Because it has not been assigned to any VLAN， interface gigabitethernet 0/1 does not appear in the show vlan output.
最新試題
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
What two things will occur when an edge port receives a BPDU？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Which statement is correct about RSTP port roles？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）