A. The additions will create more collision domains.
B. IP address utilization will be more efficient.
C. More bandwidth will be required than was needed previously.
D. An additional broadcast domain will be created.
E. The possibility that switching loops will occur will increase dramatically.
您可能感興趣的試卷
你可能感興趣的試題
A. To prevent unauthorized Telnet access to a switch port.
B. To limit the number of Layer 2 broadcasts on a particular switch port.
C. To prevent unauthorized hosts from accessing the LAN.
D. To protect the IP and MAC address of the switch and associated ports.
E. To block unauthorized access to the switch management interfaces over common TCP ports.
A. All defined VLANs are allowed on the trunk by default.
B. Each VLAN, or VLAN range, that is specified with the switchport mode command.
C. Each VLAN, or VLAN range, that is specified with the vtp domain command.
D. Each VLAN, or VLAN range, that is specified with the vlan database command.
A. a straight-through cable
B. an EIA/TIA-232 serial cable
C. an auxiliary cable
D. a modem cable
E. a cross-over cable
A. Straight-through cable
B. Compatible network interfaces
C. Networking protocol
D. Hub
E. Crossover cable
F. router
A. Rollover cable
B. Console cab le
C. Crossover cable
D. Straight-through cable
E. Serial cable
A. A broadcast domain with too many hosts.
B. Full duplex operation.
C. Broadcast storms.
D. Multicasting.
E. Network Segmentation.
F. Low bandwidth.
A. A switch.
B. A router.
C. A network adapter card.
D. A hub.
E. A repeater.
The TestKing network Topology is displayed in the exhibit below
A switch has been configured for three different VLANs: VLAN 2, VLAN 3, andVLAN 4. For the purposes of communication between VLANs a router is to beadded. Host from one VLAN should be able to reach the hosts in the other VLANs.
Based on this requirement, what type of connection is acceptable between the routerand switch?（）
A. 10 Mbps Ethernet
B. 56 kbps serial
C. 100 Mbps Ethernet
D. 1,544 Mbps serial
E. 1000 Mbps Ethernet
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network.
What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）
A. The switch that will share its VLAN configuration must be in VTP server mode.
B. The switches must be in the same VTP domain.
C. The switch that will share the VLAN information must be configured as the root bridge.
D. The switches must be connected over VLAN trunks.
E. The switches must be configured to use the same STP version.
F. The switches must have VTP pruning activated.
A. By default, all defined VLANs are allowed on the trunk.
B. Each single VLAN, or VLAN range, must be specified with the switchport mode command.
C. Each single VLAN, or VLAN range, must be specified with the vtp domain command.
D. Each single VLAN, or VLAN range, must be specified with the vlan database command.
最新試題
What feature of a networks switch allows an administrative to create separate broadcast domains?（）
Which statement describes the rule of split horizon?（）
What should the configuration register value be after successfully completing the password recover procedure and returning the router to normal operation? （）
What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）
Which of the following host addresses are member of networks that can be routed across the public Internet? （）
The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? （）
What does a configuration Register Setting of 0x2105 indicate to the Router? （）
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? （）
Which Frame Relay feature is responsible for transmitting keepalives to ensure that the PVC does not shut down because of inactivity?（）