A.NetFlow
B.SNMP
C.Debug
D.SysLog
E.EEM
F.CEF
您可能感興趣的試卷
你可能感興趣的試題
A.2811
B.2801
C.2851
D.2821
E.1841
F.3825
A.Providing technical customer support
B.Changing configurations
C.Updating software
D.Monitoring network performance
E.Replacing hardware
F.Scheduling backups
A.broadcast, multicast
B.unicast, broadcast
C.broadcast, unicast
D.multicast, unicast
E.broadcast, broadcast
F.unicast, multicast
A.A large number of BGP sessions
B.A large BGP table
C.A router is configured with the following command: ip route 0.0.0.0 0.0.0.0 fa 0/1
D.All interface buffers are continually in use
E.A flapping interface
F.The router sends a large number of ARP requests
A.May have Ethernet as well as non-Ethernet interfaces
B.Traditionally used as a standalone device for inter-VLAN communication
C.Makes use of TCAMs
D.Uses subinterfaces to define trunks
E.Can use both Layer 2 and Layer 3 to make forwarding decisions
F.Allows the definition of Switched Virtual Interfaces(SVI)
A.Use the ip nbar pdlm command to allow NBAR to reference a new PDLM in flash memory
B.If NBAR doesn’t recognize certain applications you must contact Cisco and ask them to emailyou a new PDLM for that application
C.Use the ip nbar port-map command to allow NBAR to recognize certain applications with anev/port number
D.The applications not being recognized can be rerouted to an NBAR collector, which has a morecomplete list of applications
E.Use the copy nbar flash: command to download a new PDLM file to flash
F.Use the ip nbar pdlm command to download a new NBAR reference file from the Cisco website
A.Routing loops
B.Misconfiguration of VPN end points
C.Overiapping IP address space
D.DMVPN
E.User profiles
F.MTU
Which of the following is a valid representation of the following IPv6 address:
2001:0000:0000:0abc:0000:0000:000a:000b? Choose the answer with the least number of digits.()
A.2001:0000:0:abc:0000:0000:a:b
B.2001::abc::a:b
C.2001::abc:0:0:000a:000b
D.2001::0abc:0000:0000:a:b
E.2001:0000:0000:abc::a:b
F.2001::abc:0:0:a:b
A.Quality of Service
B.Trunk configuration
C.Access lists
D.Routing protocol configuration
E.Power over Ethernet
F.DHCP configuration
A.Create an IPv4 tunnel and assign the tunnel IPv6 addresses
B.Create IPv4 interfaces on both ends of the network, and use either static routes or a routingprocess to direct IPv6 packets through those interfaces
C.IPv6 packets cannot be encapsulated with IPv4 headers because the addresses are notcompatible
D.Create IFV6 interfaces on both ends of the network, and use static routes to point the IPv4address to those interfaces
E.Use an IPv6 routing protocol like OSPFv3 and assign IPv4 packets to that process
F.Create an IPv4 tunnel and use the tunnel mode ipv6ip command
最新試題
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete?()
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
A new router was configured with the following commands:The configuration above was found on an Internet Service Provider’s (ISP) Multiprotocol LabelSwitching (MPLS) network. What is its purpose?()
Which statement about PPPoA configuration is correct?()
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions, you will need to referto the SDM and the topology, neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define?()
Network Topology Exhibit:Configuration Exhibit:NET(config)# access-list 112 deny icmp any any echo logNET(config)# access-list 112 deny imp any any redirect logNET(config)# access-list 112 deny icmp any any mask-request logNET(config)# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET(config)# interface Fa0/1NET(config-if)# ip access-group 112 inYou work as a network administrator at networkTut.com, study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However, the configurationis incorrect. On the basis of the information in the exhibit, which configuration option wouldcorrectly configure router NET?()
Drag and drop question. The upper gives the MPLS functions, the bottom describes the planes.Drag the above items to the proper location at the below
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password?()
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct?()